> A few ideas here:

> make a paper core that you leave inside. For large,cheap paper, get a hot
> iron and press out the wrinkles in a a few sheet of the morning paper.
> Roll them around any suitable form --PVC pipe, electical condit, iron
> pipe, broom sticks, closet poles etc.

> ou can also wrap these with a couple layers of wax paper, which is
> resistant to epoxy, but is slippery enough to allow you to withdraw the
> support pole. Saran wrap is a bit too 'tacky' for this, I think. A layer
> of aluminum foil might be nice if wax paper is hard to come by.

> If you want an oval cross section, use your plane, drawknife, spokshave,
> or belt sander to flatten areas along the length of a closet pole, Sand it
> smooth and maybe rub on a few coats of wax.

> The support pole you use should be at least a foot longer than the length
> of the shaft (loom?) that you are making. That way you can us a dab or
> tape at each end of your paper to tape it to the support pole. also, the
> longer length ill let you prop the ends on a pair of saw horses so that
> the resin coated glass or carbon, or whatever is suspended horizontally
> while it sets up. And if it starts to drip or sag, you can rotate the
> support pole.

> The foam pipe covers that insulate pipes can be used too. Cover them with
> a layer of waxpaper, then the resin and glass.

> I dont think you want to wrap the carbon fiber tape barberpole fashion.
> the pictures I've seen of people making fly fishing poles seem to
> emphasize that the fibers run straight for the full length for best
> strength with lightest weight. Maybe they also do this for flexibility,
> though. You may want one layer wound in a helix, covered by a layer with
> the fibers in line. Or you amy want some combination for strength and
> flexibility. After you do the first layer you can pull out your support
> rod or tube ( so it doesn't permanently stay inside) and replace it with
> smaller diameter rod, or piece of electical conduit.

> You night try reshaping a round tube into an oval by applying gentle
> pressure to it after the resin has set, and the assembly has been removed
> from the original support. It should still be workable for a few hours to
> a few days ( depending on resin/hardener and temperature). place a smaller
> diameter pole inside while you do this so you don't accidentally smash it.

> There are soft foam tubes, kind of like the foam 'pool noodles' that are
> so popular with little kids, but these are sold in smaller diameters, and
> frequently used in construction as a compressible sealing material. They
> may ot be stiff enough to use as forms for yur hollow tubes, but if they
> are wrappe with 3 or 4 layers of newsprint they get pretty stiff and weigh
> practically nothing. Poke a hole in one end and you can hang these things
> from your garage rafters to help keep them straight while the glass/resin
> sets up.

> I'm surprised Rehd didn't mention the dissolvable packing 'peanuts' that
> are made of cornstarch. Roll a tube of paper and stuff it with these to
> reinforce it before applying resin and glass. You may want to chop some of
> these into a smaller size so they fill your paper roll better. Warm water
> dissolves these things, and washes the center of your tube clean in
> minutes.

Hey, I ain't no dumby !! Why would I go and waste a perfectly good snack ?? Man, a guy could waist away if it weren't for the little snacks these nice folks provide.

Test a few to make sure you are not using expanded styrene!

Oh, you betchya. I got one once and it was a trip to the dentist to get that green stuff off the teeth. Them's some danged embarrassing questions ya gotta answer. Tastes really bad too !

So, how about taking some of that soft tubing, sliding it over a broom or rake handle, wrapping it with the news paper for rigidity, taking the handle out and filling it with the sand ( room temp ) and then doing the wax-paper, and two directional glass ( carbon? ) and then squeezing the ovals into it while the resin is still pliable. The sand will take the shape and keep it till the resin is cured. Then, you could unplug the end........oh crap, I forgot to plug the ends and the sand already leaked out. Hey, I'm only here to help a couple of friends. !!! Used to be a few. Now it's a couple, and getting fewer. Pretty soon, I can go out and start on my canoe, and won't have to worry about helping anyone. And it's almost cornstarch peanut time again!!

Rehd

(if
> you get a mixture, you can get rid of the styrene ones with acetone)

> Just few thoughts to keep you up at night.

> Paul G. Jacobson

> You can buy fiberglass and carbon fiber tubes already made. Search the web
> for antenna parts for amateur radio operators. (hams) Some people are
> using these for the longitudinal members on skin-on-frame kayaks, but I
> suspect they have an inexpensive supplier, or bought these as surplus.

> Another material you can use for cores is available at fabric stores. It
> is water soluble( or 'rinse away') fabric stabilizer. This stiff, non
> woven material is used by sewers who do embroidery. In sewing it is placed
> behind the area where an embrodered design is located in thin or sheer
> materials. You would stitch through the fabric and this stabilizer. After
> finishing, you cut or tear off the excess stabilizer, and wash the area,
> or just spritz it with water and the stabilizer dissolves away. If you
> wrap some over the support rod, after you pull out the support you simply
> rinse the inside of your tube to dissolve away this material.

> 'Styrofoam' or other expanded styrene foams can be machined with
> sandpaper, knives, hot wires, etc. to make molds for more complicated
> pieces. You can use it for long rods or tubes, too. Styrene dissolves in
> acetone -- and it is amazing how much will dissolve in just a few drops of
> acetone. Cured epoxy will withstand the action of the acetone for wuite a
> while, so after the rod is formed, pour a teaspoon of acetone into it and
> slosh this around until the styrene is dissolved. (this makes a useful mix
> of dissolved styrene, so save it in a glass jar) Or. leave the foam in the
> middle o the tube. It weighs almost nothing and can add a bit of
> stiffness.