Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Cutting strips - or burning them from the plan
By:Brian Wegener
Date: 6/9/2000, 11:25 am
In Response To: Re: Cutting strips - or burning them from the plan (Rehd)

: I'm not certain, as I'm not an electrician, but, I believe the 220v motors
: will run cheaper than the 110v. Sounds odd, but, that's what I hear. ??
: May have something to do with the fact that they don't get to full load as
: easily as the smaller motor. Don't draw as much current to do the same
: amount of work. ??

I don't know about cheaper (in terms of cost of electricity) but the 220v motor should run cooler and extend the motor life. Some of the motors on tablesaws can be wired to run 110V or 220V.

Messages In This Thread

Cutting strips - or burning them from the planks?
Greg Hughes -- 6/7/2000, 8:33 pm
Thanks for all the suggestions
Greg Hughes -- 6/8/2000, 10:05 pm
Re: Thanks for all the suggestions
Rehd -- 6/10/2000, 1:11 am
Re: Cutting strips - or burning them from the plan
mike allen ---> -- 6/8/2000, 12:37 pm
Re: Cutting strips - or burning them from the plan
Don Bowen -- 6/8/2000, 1:08 pm
Re: Cutting strips - use small wedges when needed
Hank -- 6/8/2000, 8:22 am
Re: Cutting strips - use small wedges when needed
Brian Wegener -- 6/9/2000, 11:08 am
Re: Cutting strips - or burning them from the plan
michael -- 6/8/2000, 6:34 am
Re: Cutting strips - or burning them from the plan
Don Bowen -- 6/8/2000, 10:36 am
Re: Cutting strips - or burning them from the plan
Charles Cooper -- 6/8/2000, 11:19 am
Re: Cutting strips - I forgot......
michael -- 6/9/2000, 5:24 am
Re: Cutting strips - or burning them from the plan
Charles Cooper -- 6/7/2000, 11:32 pm
Hate to ask but gotta
Tom Kurth -- 6/7/2000, 9:48 pm
Re: Cutting strips - or burning them from the plan
Rehd -- 6/7/2000, 9:07 pm
Re: Cutting strips - or burning them from the plan
bob -- 6/8/2000, 11:23 pm
Re: Cutting strips - or burning them from the plan
Rehd -- 6/9/2000, 1:11 am
Re: Cutting strips - or burning them from the plan
bob -- 6/10/2000, 8:24 am
Re: Cutting strips - or burning them from the plan
Rehd -- 6/10/2000, 11:02 pm
Re: Cutting strips - or burning them from the plan
Rehd -- 6/9/2000, 1:19 am
Re: Cutting strips - or burning them from the plan
Brian Wegener -- 6/9/2000, 11:25 am
Re: Cutting strips - or burning them from the plan
Don Bowen -- 6/9/2000, 12:45 pm
Re: Cutting strips - or burning them from the plan
Spidey -- 6/9/2000, 10:05 pm
Re: Cutting strips - or burning them from the plan
Rehd -- 6/10/2000, 12:53 am
Re: Cutting strips - or burning them from the plan
Don -- 6/7/2000, 9:18 pm
Re: Cutting strips - or burning them from the plan
Rehd -- 6/7/2000, 9:26 pm
Re: Cutting strips - or burning them from the plan
JG -- 6/8/2000, 3:47 am
Re: Cutting strips - or burning them from the plan
Rehd -- 6/8/2000, 9:37 am
Re: Cutting strips - or burning them from the plan
JG -- 6/8/2000, 3:06 pm
Re: Cutting strips - or burning them from the plan
Rehd -- 6/8/2000, 7:20 pm
Re: Cutting strips - or burning them from the plan
JG -- 6/9/2000, 2:12 pm
Re: Cutting strips - or burning them from the plan
Spidey -- 6/7/2000, 8:58 pm
Re: Cutting strips - or burning them from the plan
Rehd -- 6/7/2000, 9:15 pm
Re: Cutting strips - or burning them from the plan
Dean Trexel -- 6/7/2000, 8:57 pm