Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Stiff roller--good idea.
By:John Monfoe
Date: 2/16/2001, 4:37 am
In Response To: Re: About to Fiberglass a Stripper 1st time (Arthur)

One thing that I should
: have realized eariler but didn't : the small roller frame had gotten some
: epoxy inbetween the center wire support and the "roller" part
: itself. This caused the roller to be very stiff. I worked it (late at
: night and it was the only one I had) and cut at it and put a small amount
: of lube and it loosened up, but it was still not really "free"
: rolling. In the event I think this helped me put a very thin layer of
: epoxy on the hull. The "stiffness" of the roller caused me to
: apply more pressure and this cut way, way down on the production of
: bubbles. In fact I had almost no bubbles at all. The extra smoothing I
: gave the seal coat allowed a remarkably tight laying of the glass. That
: combined with the thin layer of epoxy put on by my stiff roller made the
: job go very eaisily. No mess, no runs, and when I went over the boat with
: the squeegee

Hi Arthur,
You may have discovered something. When I start to fiberglass I am thinking about making a stiff roller with some kind of a jam. I would take it out so I could roll and load up the roller and then put in the jam. As you found out, you would be putting on a starved coat and pushing out bubbles while the roller would have a gravity feed from the excess epoxy flowing down to the bottom of the roller.

John

Messages In This Thread

About to Fiberglass a Stripper 1st time
Arthur -- 2/8/2001, 4:13 am
Re: About to Fiberglass a Stripper 1st time
Arthur -- 2/15/2001, 5:48 am
Stiff roller--good idea.
John Monfoe -- 2/16/2001, 4:37 am
Resin use
Paul G. Jacobson -- 2/16/2001, 3:53 am
Re: Resin use
Richard Boyle -- 2/16/2001, 8:21 am
Re: About to Fiberglass a Stripper 1st time
Jim Sailer -- 2/9/2001, 9:37 am
Re: About to Fiberglass a Stripper 1st time *Pic*
Rob Macks -- 2/8/2001, 11:23 am
Re: About to Fiberglass a Stripper 1st time
Arthur -- 2/20/2001, 7:32 pm
Re: About to Fiberglass a Stripper 1st time
Rob Macks -- 2/20/2001, 10:53 pm
Re: About to Fiberglass a Stripper 1st time
Arthur -- 2/9/2001, 3:06 am
Re: About to Fiberglass a Stripper 1st time
Rob Macks -- 2/9/2001, 12:05 pm
staples/no staples
Sam McFadden -- 2/10/2001, 1:53 pm
Re: Slight Disagreement . . .
Spidey -- 2/9/2001, 10:48 pm
What you want
Nick Schade - Guillemot Kayaks -- 2/10/2001, 10:32 am
Some points
mike allen -- 2/12/2001, 12:20 pm
Re: Internal Strongback
Nick Schade - Guillemot Kayaks -- 2/13/2001, 9:39 am
Internal Strongback confined releases
mike allen -- 2/13/2001, 12:13 pm
Re: Internal Strongback confined releases
Nick Schade - Guillemot Kayaks -- 2/14/2001, 9:22 am
Re: Internal Strongback confined releases
mike allen ---> -- 2/14/2001, 11:42 am
Re: What you want
Spidey -- 2/10/2001, 12:19 pm
Re: Well said!
Don Beale -- 2/10/2001, 11:00 am
Re: Slight Disagreement . . .
Rob Macks -- 2/10/2001, 12:08 am
Re: Slight Disagreement . . .
Richard Boyle -- 2/10/2001, 8:48 am
Re: Slight Disagreement . . .
Rob Macks -- 2/10/2001, 9:37 am
Re: Fell out of my chair laughing!
Spidey -- 2/10/2001, 12:45 am
Re: Slight Disagreement . . .
Rehd -- 2/10/2001, 12:24 am
Re: Might have to..........
Rehd -- 2/9/2001, 11:25 pm
Re: uneven seal coats
Nick Schade - Guillemot Kayaks -- 2/9/2001, 6:12 pm
Re: uneven seal coats
Al Gunther -- 2/10/2001, 11:49 am
Re: About to Fiberglass a Stripper 1st time
Arthur -- 2/9/2001, 2:49 pm
Re: About to Fiberglass a Stripper 1st time
Arthur -- 2/8/2001, 9:14 pm
Re: About to Fiberglass a Stripper 1st time
Dale Frolander -- 2/8/2001, 4:16 pm
Re: About to Fiberglass a Stripper 1st time
Ray Port Angeles -- 2/10/2001, 12:09 pm
Re: About to Fiberglass a Stripper 1st time
Les Corley -- 2/8/2001, 6:57 pm
Re: About to Fiberglass a Stripper 1st time
Rob Macks -- 2/8/2001, 7:20 pm
Just in time
Angela Watson -- 2/8/2001, 12:20 pm
Re: Just in time
Angela Watson -- 2/11/2001, 7:01 pm
Re: Just in time
Don Beale -- 2/8/2001, 7:12 pm
Re: Just in time
Angela Watson -- 2/8/2001, 9:13 pm
Re: Just in time
Don Beale -- 2/9/2001, 12:06 pm
Re:Keep the FOCUS..work is good..keys,wheres my ke *NM*
Ben Staley -- 2/9/2001, 12:58 pm
Re:And remember..
Don Beale -- 2/11/2001, 12:32 pm
Re: Just in time *Pic*
Bobby Curtis -- 2/8/2001, 1:34 pm
Re: Just in time
Angela Watson -- 2/8/2001, 7:04 pm
Re: Just in time
Angela Watson -- 2/8/2001, 7:12 pm
Re: Just in time
Bobby Curtis -- 2/8/2001, 7:41 pm
Re: Just in time
Geo. Cushing -- 2/8/2001, 12:59 pm
Re: Just in time
Angela Watson -- 2/8/2001, 6:56 pm
Re: Glassing time
Ben Staley -- 2/8/2001, 12:32 pm
Glassing
Russ -- 2/8/2001, 8:44 am