Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Cheek Plate Safety
By:Jim
Date: 5/18/2001, 5:11 pm
In Response To: Re: Cheek Plate Safety (Ben Staley)

: Good question, my minicell seat is higher than the gap underneath the cheek
: plate so it hasn't been a problem, its covered up.

: Now I wish I had extended them to the hull and glassed them in for strength
: reasons, and I do like Shawns method of locking the boat up. I'm going to
: use a stainless u-bolt epoxied thru the bulkhead for the same.

I saw mentioned on the techniques board that some put a u-bolt on the deck just in front of the cockpit. It provides an attachment point for equipment leashes, tow line and lock-up. This was in addition to a couple cleats on each side with bungees and balls for parking paddles, etc. I know a lot of people don't want to see anything but wood but I think I'll probably have a couple fixtures on the deck like this.

Messages In This Thread

Cheek Plate Size
Mike felepchuk -- 5/17/2001, 10:16 pm
Re: Cheek Plate Size
Kent LeBoutillier -- 5/18/2001, 5:58 am
Re: Cheek Plate Safety
Mike Felepchuk -- 5/18/2001, 3:00 pm
Re: Cheek Plate Safety
Jim Pace -- 5/18/2001, 4:51 pm
Re: Cheek Plate Safety
Mike felepchuk -- 5/18/2001, 10:26 pm
Re: no worries
LeeG -- 5/19/2001, 8:41 am
Re: Cheek Plate Safety
Ben Staley -- 5/18/2001, 4:36 pm
Re: Cheek Plate Safety
Jim -- 5/18/2001, 5:11 pm
Re: U-bolts
Shawn Baker -- 5/18/2001, 4:40 pm
Re: U-bolts
Ben Staley -- 5/18/2001, 4:52 pm
Re: U-bolts
LeeG -- 5/19/2001, 8:48 am
Re: U-bolts
Shawn Baker -- 5/18/2001, 6:17 pm
Re: Cheek Plate Size
Brian Nystrom -- 5/18/2001, 12:31 pm
Re: Cheek Plate Size
Jim -- 5/18/2001, 1:22 pm
Re: Cheek Plate Size
Richard Boyle -- 5/18/2001, 3:30 pm
Re: Cheek Plates
Jim -- 5/18/2001, 4:17 pm
Re: Cheek Plates
LeeG -- 5/19/2001, 8:37 am
Re: Cheek Plate Size
Shawn Baker -- 5/18/2001, 3:18 pm
Re: Cheek Plate Size
Jim -- 5/18/2001, 4:22 pm
Re: Cheek Plate Size
Shawn Baker -- 5/18/2001, 4:38 pm
Re: Cheek Plate Size
Jim -- 5/18/2001, 5:41 pm
Re: Cheek Plate Size
LeeG -- 5/19/2001, 8:34 am
Re: Cheek Plate Size
Jim -- 5/19/2001, 9:55 am
Planetary Gear link
Jim Pace -- 5/19/2001, 10:38 am
Interesting and pretty cheap-thx *NM*
Jim -- 5/21/2001, 11:27 am
Re: Cheek Plate Size
Shawn Baker -- 5/18/2001, 6:20 pm
Re: Just snug ok-Thanks *NM*
Jim -- 5/18/2001, 6:38 pm
Re: Cheek Plate Size
Kent LeBoutillier -- 5/18/2001, 12:57 pm
Yeah, that works. *NM*
Brian Nystrom -- 5/18/2001, 3:47 pm
Re: Cheek Plate attachment to coaming
Ben Staley -- 5/18/2001, 12:54 pm
Re: Cheek Plate attachment to coaming
Nick Schade - Guillemot Kayaks -- 5/18/2001, 1:29 pm
Re: Cheek Plate Size
Richard Boyle -- 5/18/2001, 12:53 pm
Oops! My mistake.
Brian Nystrom -- 5/18/2001, 3:45 pm