Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Breather hole - How much pressure?
By:Mark Kanzler
Date: 7/4/1998, 5:37 pm
In Response To: Re: Breather hole - is it necessary? (Mark Kanzler)

Well, as you predicted, I figured it out. My thermodynamics book was covered in dust, but I found it. After looking up the properties for air, here are the calculated results.

Air, start at 110 deg F (570 R) ending at 70 deg F (530 R) adiabatic cooling, constant volume, yadda yadda yadda.

14.7-11.4 = 3.3 psi Delta P

for circular hatches:

6" dia : 93.2 Lb force to pull open hatch.

10" dia: 258.8 Lb

12" dia: 372.7 Lb

> Keep in mind that you might put the hatches onto a hot boat ashore,
> and then form a vacuum as the boat cools in the water. If it's a perfect
> seal, it could make it really tough to remove the hatch.

> Anyone want to check the steam tables to see how much delta pressure
> for moist air going from 110 deg to 70 deg? It sounds like a large
> temp chng, but I think that's quite feasible.

Messages In This Thread

Hatch seal
Mark Bodnar -- 6/26/1998, 3:44 pm
Re: Hatch seal: discerning highs and lows
Mark Kanzler -- 6/29/1998, 6:35 pm
Re: Hatch seal
NPenney -- 6/29/1998, 4:43 pm
Re: Hatch seal
Chris Boucher -- 6/29/1998, 10:07 am
Re: Hatch seal
Jay Babina -- 6/29/1998, 8:50 am
threaded rod description please?
Ross Leidy -- 6/29/1998, 9:18 am
Re: threaded rod description please?
Mark Kanzler -- 6/30/1998, 1:10 pm
Re: threaded rod description please?
Jay Babina -- 6/30/1998, 11:45 am
threaded rod questions
Mark Bodnar -- 7/3/1998, 10:00 pm
Re: threaded rod questions
Jay Babina -- 7/5/1998, 10:10 am
Re: threaded rod questions
Paul Jacobson -- 7/4/1998, 8:10 pm
Re: Doll Stock
Mark Kanzler -- 7/6/1998, 1:13 pm
Re: threaded rod questions
Tor-Henrik Furmyr -- 7/4/1998, 4:19 am
Re: threaded rod questions
Mark Kanzler -- 7/4/1998, 10:28 am
Re: Hatch - flush mount...
Tor-Henrik Furmyr -- 7/4/1998, 3:37 pm
Re: Hatch - flush mount...
Mark Kanzler -- 7/6/1998, 1:06 pm
Re: Hatch - flush mount...
Paul Jacobson -- 7/6/1998, 5:51 pm
Re: Hatch - flush mount...
Mark Kanzler -- 7/6/1998, 6:21 pm
Re: Hatch - flush mount...
Mike Spence -- 7/4/1998, 11:19 pm
Re: Impress us....
Tor-Henrik Furmyr -- 7/5/1998, 4:10 am
Re: Impress us.... -- I'll try!
Mike Spence -- 7/5/1998, 11:48 am
Re: Impress us.... -- I'll try!
Nick Schade -- 7/5/1998, 10:43 pm
Re: Impress us.... -- I'll try!
jim champoux -- 7/6/1998, 5:45 pm
Re: Impress us.... -- I'll try!
npenney@erols.com -- 7/7/1998, 8:22 pm
Re: Metal and compasses
Nick Schade -- 7/7/1998, 2:16 pm
Re: Impress us.... -- I'll try!
Mark Kanzler -- 7/6/1998, 6:06 pm
Re: Impress us.... -- I'll try!
Tor-Henrik Furmyr -- 7/5/1998, 1:33 pm
Breather hole - is it necessary?
Mike Spence -- 7/3/1998, 1:20 pm
Re: Breather hole - is it necessary?
Jay Babina -- 7/3/1998, 3:29 pm
Re: Breather hole - is it necessary?
Nick Schade -- 7/4/1998, 5:50 pm
Re: Breather hole - is it necessary?
Mark Kanzler -- 7/4/1998, 10:34 am
Re: Breather hole - How much pressure?
Mark Kanzler -- 7/4/1998, 5:37 pm
Re: threaded rod -DRAWING
Tor-Henrik Furmyr -- 7/3/1998, 6:27 am
Re: threaded rod -DRAWING (Very Nice)
Mark Kanzler -- 7/3/1998, 10:06 am
Re: threaded rod description please?
Ross Leidy -- 7/1/1998, 12:14 am
Re: threaded rod picture please?
Mark Kanzler -- 6/30/1998, 11:57 am
Re: threaded rod picture please?
Jay Babina -- 6/30/1998, 7:37 pm
Re: Email address (Mine and everyone's)
Mark Kanzler -- 7/1/1998, 10:59 am
Re: Hatch seal
Rob Forsell -- 6/27/1998, 10:34 am
Re: Hatch seal
Paul Jacobson -- 6/26/1998, 10:04 pm
Re: Hatch seal
Rick C. -- 6/28/1998, 11:37 pm
Re: Hatch seal
Mark Bodnar -- 7/1/1998, 11:02 am
Re: Hatch seal
David Dick -- 6/26/1998, 8:29 pm
Re: Hatch seal
Jerry Weinraub -- 6/26/1998, 7:14 pm
Re: Hatch seal
Mark Kanzler -- 6/26/1998, 4:51 pm
Re: Hatch seal
Mark Bodnar -- 6/26/1998, 8:05 pm