Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Venting A Sealed Compartment
By:L.C.
Date: 9/15/1998, 7:26 pm
In Response To: Venting A Sealed Compartment (Jim Ward)

> Okay, here's one for you to ponder. I'm not going to put a hatch in the
> foredeck of my Chesepeake 17. So, the foredeck bilge compartment will be
> completely sealed and therefore subject to expansion and contraction as
> the temperature changes unless I vent it. However, if I vent it with a
> small hole in the bulkhead, this could let water into this compartment. I
> can just envision this area puffing up like a plastic gas can sitting in
> the sun without the vent open. I've considered dozen of different
> solutions, but am not satisfied with any of them. Anyone have a solution?

> Thanks to all that respond.

> Jim...

Jim, I too had not wanted to put a hatch in my Pygmy Coho but, after much thought I went with the hatch. If you are going to the trouble of installing a bulkhead and I hope you mean a plywood bulkhead that is epoxied in, Why stop there? PUT THE HATCH IN!!! You wont regret it.

Larry

Messages In This Thread

Venting A Sealed Compartment
Jim Ward -- 9/15/1998, 4:16 pm
Everyone wants to vent
Paul Jacobson -- 9/18/1998, 4:19 am
Re: Everyone wants to vent
Rick VanBuren -- 9/18/1998, 4:38 pm
vent and w(h)ine
Paul Jacobson -- 9/19/1998, 9:26 pm
Re: Everyone wants to vent
Mike Spence -- 9/18/1998, 3:14 pm
Re: Venting - it's not a problem
Jay Babina -- 9/17/1998, 10:06 am
Re: Venting A Sealed Compartment
Pat Pavlik -- 9/16/1998, 10:56 pm
Re: Venting A Sealed Compartment
Mark Kanzler -- 9/16/1998, 4:02 pm
Re: Venting A Sealed Compartment
Jon K. -- 9/15/1998, 7:40 pm
Re: Venting A Sealed Compartment - MY SOLUTION
Jim Ward -- 9/15/1998, 8:59 pm
Re: Venting A Sealed Compartment - MY SOLUTION
Mark Kanzler -- 9/16/1998, 11:35 am
Re: Venting A Sealed Compartment - MY SOLUTION
Nolan Penney -- 9/16/1998, 8:45 am
Re: Venting A Sealed Compartment - MY SOLUTION
Scotty -- 9/16/1998, 11:28 am
Comments on Your Solution
Jon K. -- 9/15/1998, 10:49 pm
Re: No Foam. Inspection Port In Bulkhead
Jim Ward -- 9/16/1998, 10:28 pm
Re: No Foam. Inspection Port In Bulkhead
Mark Kanzler -- 9/18/1998, 5:35 pm
Re: No Foam. Inspection Port In Bulkhead
Mark Kanzler -- 9/18/1998, 5:55 pm
Re: No Foam. Inspection Port In Bulkhead
Nick Schade -- 9/17/1998, 5:01 pm
Re: PVC pipe fittings
Nolan Penney -- 9/17/1998, 8:01 am
Re: No Foam. Inspection Port In Bulkhead
Mike Spence -- 9/17/1998, 12:50 pm
Re: No Foam. Inspection Port In Bulkhead
Rick VanBuren -- 9/17/1998, 4:17 pm
Re: No Foam. Inspection Port In Bulkhead
Pat Pavlik -- 9/16/1998, 11:56 pm
Flexible inspection plate
Mike Spence -- 9/17/1998, 12:17 pm
Re: Venting A Sealed Compartment
L.C. -- 9/15/1998, 7:26 pm
Re: Venting A Sealed Compartment
Mark Kanzler -- 9/15/1998, 5:46 pm
Re: Venting A Sealed Compartment
Mark Carroll -- 9/15/1998, 4:46 pm
Re: Venting A Sealed Compartment
Jim Ward -- 9/15/1998, 5:23 pm
Re: Venting A Sealed Compartment
Ross Leidy -- 9/15/1998, 4:34 pm
Re: Venting A Sealed Compartment
Martin Foil -- 9/16/1998, 3:10 pm
run a vent tube
Brian C. -- 9/15/1998, 5:30 pm
Re: run a vent tube
Jim Ward -- 9/15/1998, 6:19 pm
Re: run a vent tube
Rick C. -- 9/17/1998, 10:15 pm
Re: run a vent tube
Mark Kanzler -- 9/18/1998, 6:42 pm
Re: Gas mask valve
Mike Spence -- 9/18/1998, 3:01 am
Re: Gas mask valve
Mark Kanzler -- 9/18/1998, 6:55 pm
Re: Gas mask valve
Nolan Penney -- 9/18/1998, 7:01 am
Re: Gas mask valve
Mark Kanzler -- 9/18/1998, 7:03 pm
Re: Tandem valve....
Tor-Henrik Furmyr -- 9/19/1998, 6:42 pm
Re: Tandem valve....
Mark Kanzler -- 9/20/1998, 1:06 am
valveless `valve'
Paul Jacobson -- 9/19/1998, 8:44 pm
Re: Gas mask valve
Rick C. -- 9/18/1998, 2:28 pm
Re: Venting A Sealed Compartment
Jim Ward -- 9/15/1998, 5:28 pm
Re: Idea #2
Nick Schade -- 9/16/1998, 5:57 pm
Re: Venting A Sealed Compartment
Nick Schade -- 9/16/1998, 5:44 pm
Re: Venting A Sealed Compartment
Ross Leidy -- 9/15/1998, 5:52 pm