Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Venting A Sealed Compartment
By:Pat Pavlik
Date: 9/16/1998, 10:56 pm
In Response To: Venting A Sealed Compartment (Jim Ward)

I will guess that you do not want to put in a standard hatch for appearance reasons. If so, would you consider an inspection cover on the foredeck, one that blends in with the foredeck and provides a water proof seal yet offers some pressure relief. Using the same blank that you cut out of the foredeck for the inspection opening could do this. Or, could you combine a compass and a vent/small inspection opening? A less serious idea is to pull a partial vacuum on the compartment and then seal it so that the peak pressure is less than it otherwise would be.

From what has been posted, it could be risky to have a vent hole, a source for water entry, without an inspection hatch, even a vent protected with a tube and bladder system. Regarding the foam idea, what if you damage the hull and a small leak lets water in which soaks into the foam? Good luck!

> Okay, here's one for you to ponder. I'm not going to put a hatch in the
> foredeck of my Chesepeake 17. So, the foredeck bilge compartment will be
> completely sealed and therefore subject to expansion and contraction as
> the temperature changes unless I vent it. However, if I vent it with a
> small hole in the bulkhead, this could let water into this compartment. I
> can just envision this area puffing up like a plastic gas can sitting in
> the sun without the vent open. I've considered dozen of different
> solutions, but am not satisfied with any of them. Anyone have a solution?

> Thanks to all that respond.

> Jim...

Messages In This Thread

Venting A Sealed Compartment
Jim Ward -- 9/15/1998, 4:16 pm
Everyone wants to vent
Paul Jacobson -- 9/18/1998, 4:19 am
Re: Everyone wants to vent
Rick VanBuren -- 9/18/1998, 4:38 pm
vent and w(h)ine
Paul Jacobson -- 9/19/1998, 9:26 pm
Re: Everyone wants to vent
Mike Spence -- 9/18/1998, 3:14 pm
Re: Venting - it's not a problem
Jay Babina -- 9/17/1998, 10:06 am
Re: Venting A Sealed Compartment
Pat Pavlik -- 9/16/1998, 10:56 pm
Re: Venting A Sealed Compartment
Mark Kanzler -- 9/16/1998, 4:02 pm
Re: Venting A Sealed Compartment
Jon K. -- 9/15/1998, 7:40 pm
Re: Venting A Sealed Compartment - MY SOLUTION
Jim Ward -- 9/15/1998, 8:59 pm
Re: Venting A Sealed Compartment - MY SOLUTION
Mark Kanzler -- 9/16/1998, 11:35 am
Re: Venting A Sealed Compartment - MY SOLUTION
Nolan Penney -- 9/16/1998, 8:45 am
Re: Venting A Sealed Compartment - MY SOLUTION
Scotty -- 9/16/1998, 11:28 am
Comments on Your Solution
Jon K. -- 9/15/1998, 10:49 pm
Re: No Foam. Inspection Port In Bulkhead
Jim Ward -- 9/16/1998, 10:28 pm
Re: No Foam. Inspection Port In Bulkhead
Mark Kanzler -- 9/18/1998, 5:35 pm
Re: No Foam. Inspection Port In Bulkhead
Mark Kanzler -- 9/18/1998, 5:55 pm
Re: No Foam. Inspection Port In Bulkhead
Nick Schade -- 9/17/1998, 5:01 pm
Re: PVC pipe fittings
Nolan Penney -- 9/17/1998, 8:01 am
Re: No Foam. Inspection Port In Bulkhead
Mike Spence -- 9/17/1998, 12:50 pm
Re: No Foam. Inspection Port In Bulkhead
Rick VanBuren -- 9/17/1998, 4:17 pm
Re: No Foam. Inspection Port In Bulkhead
Pat Pavlik -- 9/16/1998, 11:56 pm
Flexible inspection plate
Mike Spence -- 9/17/1998, 12:17 pm
Re: Venting A Sealed Compartment
L.C. -- 9/15/1998, 7:26 pm
Re: Venting A Sealed Compartment
Mark Kanzler -- 9/15/1998, 5:46 pm
Re: Venting A Sealed Compartment
Mark Carroll -- 9/15/1998, 4:46 pm
Re: Venting A Sealed Compartment
Jim Ward -- 9/15/1998, 5:23 pm
Re: Venting A Sealed Compartment
Ross Leidy -- 9/15/1998, 4:34 pm
Re: Venting A Sealed Compartment
Martin Foil -- 9/16/1998, 3:10 pm
run a vent tube
Brian C. -- 9/15/1998, 5:30 pm
Re: run a vent tube
Jim Ward -- 9/15/1998, 6:19 pm
Re: run a vent tube
Rick C. -- 9/17/1998, 10:15 pm
Re: run a vent tube
Mark Kanzler -- 9/18/1998, 6:42 pm
Re: Gas mask valve
Mike Spence -- 9/18/1998, 3:01 am
Re: Gas mask valve
Mark Kanzler -- 9/18/1998, 6:55 pm
Re: Gas mask valve
Nolan Penney -- 9/18/1998, 7:01 am
Re: Gas mask valve
Mark Kanzler -- 9/18/1998, 7:03 pm
Re: Tandem valve....
Tor-Henrik Furmyr -- 9/19/1998, 6:42 pm
Re: Tandem valve....
Mark Kanzler -- 9/20/1998, 1:06 am
valveless `valve'
Paul Jacobson -- 9/19/1998, 8:44 pm
Re: Gas mask valve
Rick C. -- 9/18/1998, 2:28 pm
Re: Venting A Sealed Compartment
Jim Ward -- 9/15/1998, 5:28 pm
Re: Idea #2
Nick Schade -- 9/16/1998, 5:57 pm
Re: Venting A Sealed Compartment
Nick Schade -- 9/16/1998, 5:44 pm
Re: Venting A Sealed Compartment
Ross Leidy -- 9/15/1998, 5:52 pm