Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: run a vent tube
By:Rick C.
Date: 9/17/1998, 10:15 pm
In Response To: Re: run a vent tube (Jim Ward)

Hi howdy,

Next to the rubber disc with a small pierce, I like this idea best. You can get very small tubing, and then run it along a sheer clamp or seam and epoxy it in. Or, glue it to the top of the inside of the deck.

Here is another thought I just had. Install some kind of one way valve. A small round piece, with some kind of stiff flapper on it. Air under preasure would be forced out, but nothing can get in. It's the same principal as used on an M-17 gas mask. You could probably find one at an Army Surplus, and simply cut the valve right out of the cheek-piece.

What-da-ya-think Mark? I'll hafta mull this one over fer a while, n' see what I can think of.

Good luck,

Rick C.

Messages In This Thread

Venting A Sealed Compartment
Jim Ward -- 9/15/1998, 4:16 pm
Everyone wants to vent
Paul Jacobson -- 9/18/1998, 4:19 am
Re: Everyone wants to vent
Rick VanBuren -- 9/18/1998, 4:38 pm
vent and w(h)ine
Paul Jacobson -- 9/19/1998, 9:26 pm
Re: Everyone wants to vent
Mike Spence -- 9/18/1998, 3:14 pm
Re: Venting - it's not a problem
Jay Babina -- 9/17/1998, 10:06 am
Re: Venting A Sealed Compartment
Pat Pavlik -- 9/16/1998, 10:56 pm
Re: Venting A Sealed Compartment
Mark Kanzler -- 9/16/1998, 4:02 pm
Re: Venting A Sealed Compartment
Jon K. -- 9/15/1998, 7:40 pm
Re: Venting A Sealed Compartment - MY SOLUTION
Jim Ward -- 9/15/1998, 8:59 pm
Re: Venting A Sealed Compartment - MY SOLUTION
Mark Kanzler -- 9/16/1998, 11:35 am
Re: Venting A Sealed Compartment - MY SOLUTION
Nolan Penney -- 9/16/1998, 8:45 am
Re: Venting A Sealed Compartment - MY SOLUTION
Scotty -- 9/16/1998, 11:28 am
Comments on Your Solution
Jon K. -- 9/15/1998, 10:49 pm
Re: No Foam. Inspection Port In Bulkhead
Jim Ward -- 9/16/1998, 10:28 pm
Re: No Foam. Inspection Port In Bulkhead
Mark Kanzler -- 9/18/1998, 5:35 pm
Re: No Foam. Inspection Port In Bulkhead
Mark Kanzler -- 9/18/1998, 5:55 pm
Re: No Foam. Inspection Port In Bulkhead
Nick Schade -- 9/17/1998, 5:01 pm
Re: PVC pipe fittings
Nolan Penney -- 9/17/1998, 8:01 am
Re: No Foam. Inspection Port In Bulkhead
Mike Spence -- 9/17/1998, 12:50 pm
Re: No Foam. Inspection Port In Bulkhead
Rick VanBuren -- 9/17/1998, 4:17 pm
Re: No Foam. Inspection Port In Bulkhead
Pat Pavlik -- 9/16/1998, 11:56 pm
Flexible inspection plate
Mike Spence -- 9/17/1998, 12:17 pm
Re: Venting A Sealed Compartment
L.C. -- 9/15/1998, 7:26 pm
Re: Venting A Sealed Compartment
Mark Kanzler -- 9/15/1998, 5:46 pm
Re: Venting A Sealed Compartment
Mark Carroll -- 9/15/1998, 4:46 pm
Re: Venting A Sealed Compartment
Jim Ward -- 9/15/1998, 5:23 pm
Re: Venting A Sealed Compartment
Ross Leidy -- 9/15/1998, 4:34 pm
Re: Venting A Sealed Compartment
Martin Foil -- 9/16/1998, 3:10 pm
run a vent tube
Brian C. -- 9/15/1998, 5:30 pm
Re: run a vent tube
Jim Ward -- 9/15/1998, 6:19 pm
Re: run a vent tube
Rick C. -- 9/17/1998, 10:15 pm
Re: run a vent tube
Mark Kanzler -- 9/18/1998, 6:42 pm
Re: Gas mask valve
Mike Spence -- 9/18/1998, 3:01 am
Re: Gas mask valve
Mark Kanzler -- 9/18/1998, 6:55 pm
Re: Gas mask valve
Nolan Penney -- 9/18/1998, 7:01 am
Re: Gas mask valve
Mark Kanzler -- 9/18/1998, 7:03 pm
Re: Tandem valve....
Tor-Henrik Furmyr -- 9/19/1998, 6:42 pm
Re: Tandem valve....
Mark Kanzler -- 9/20/1998, 1:06 am
valveless `valve'
Paul Jacobson -- 9/19/1998, 8:44 pm
Re: Gas mask valve
Rick C. -- 9/18/1998, 2:28 pm
Re: Venting A Sealed Compartment
Jim Ward -- 9/15/1998, 5:28 pm
Re: Idea #2
Nick Schade -- 9/16/1998, 5:57 pm
Re: Venting A Sealed Compartment
Nick Schade -- 9/16/1998, 5:44 pm
Re: Venting A Sealed Compartment
Ross Leidy -- 9/15/1998, 5:52 pm