Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: How to copy a hull?
By:Nolan Penney
Date: 10/5/1998, 6:16 am
In Response To: Re: How to copy a hull? (Paul A. Lambert)

> I buy a very roll of heavy plumbers solder and then I bend it around the
> hull at pre-determined points along the keel, I can transfer the shape to
> paper and then make an offset table from it. You will need to know the
> beam at each point as you put it on paper.I wish I thought up this trick,
> but it has been used in England for years.

A very nice and simple technique. I like it. A wire alternative that might be worth investigating is the type of wire used to hang drop ceilings. It's got the basic personality of solder, but is probably a lot cheaper.

Messages In This Thread

How to copy a hull?
Fritjof -- 10/2/1998, 11:32 am
here's your 'lazer' survey
Brian C. -- 10/6/1998, 2:22 pm
Re: How to copy a hull?
Paul Jacobson -- 10/4/1998, 2:01 am
Re: How to copy a hull?
Mark Kanzler -- 10/4/1998, 10:30 am
Re: How to copy a hull?
Steve Bradbury -- 10/4/1998, 8:20 am
Re: How to copy a hull?
Mark Kanzler -- 10/4/1998, 10:43 am
Re: How to copy a hull?
Paul Jacobson -- 10/4/1998, 8:38 pm
Re: How to make flat patterns.
Mark Kanzler -- 10/4/1998, 8:55 pm
Re: How to copy a hull?
Mike Scarborough -- 10/4/1998, 7:09 pm
Re: How to copy a hull?
Mark Kanzler -- 10/5/1998, 10:54 am
Re: How to copy a hull?
Jay Babina -- 10/2/1998, 3:33 pm
Re: Picture of... How to copy a hull?
Edgar Kleindinst -- 10/10/1998, 6:52 pm
Re: Picture of... How to copy a hull?
Nick Schade -- 10/11/1998, 10:02 am
Re: Another Picture of... How to copy a hull?
Edgar Kleindinst -- 10/11/1998, 6:32 pm
Re: Another Picture of... How to copy a hull?
Brian C. -- 10/12/1998, 2:14 pm
Re: Another Picture of... How to copy a hull?
Jay Babina -- 10/13/1998, 12:55 am
Re: Another Picture of... How to copy a hull?
Edgar Kleindinst -- 10/12/1998, 1:58 pm
Re: Picture of... How to copy a hull?
Mark Kanzler -- 10/11/1998, 10:43 am
Re: How to copy a hull?
Mike Scarborough -- 10/2/1998, 3:15 pm
Re: How to copy a hull.
Mark Kanzler -- 10/3/1998, 12:46 am
Re: How to copy a hull.
Paul Jacobson -- 10/4/1998, 9:24 pm
Re: How to copy a hull.
Mike Spence -- 10/2/1998, 8:59 pm
Re: How to copy a hull.
Mark Kanzler -- 10/4/1998, 10:54 am
Re: How to copy a hull?
Paul A. Lambert -- 10/3/1998, 12:40 am
Re: How to copy a hull?
Nolan Penney -- 10/5/1998, 6:16 am
Re: How to copy a hull?
Nolan Penney -- 10/3/1998, 12:06 am