Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Is this the same problem?
By:Gordon Niessen
Date: 12/15/2004, 2:18 pm
In Response To: Re: Is this the same problem? (Rob Macks)

I always thought it was due to incomplete saturation and some moisture trapped in the weave of the glass. Where trapped air is immediately visible, the moisture does not be come visible until the heat causes it to expand and turn into a gas. No scientific proof of this. But that is what I always blamed it on when it happen to me a week or more after glassing. Here in Houston it is hard to keep humitity out of any project.

My two cents worth. For a full, refund send a stamped self address envelope.

Messages In This Thread

Epoxy: Out of the Pit of Dispair
Rob Macks -- 12/14/2004, 5:14 pm
Re: Epoxy: Out of the Pit of Dispair
Nick Schade - Guillemot Kayaks -- 12/15/2004, 2:31 pm
Glass workers do the same thing, Nick
Robert N Pruden -- 12/16/2004, 11:32 am
Solar post-curing?
Brian Nystrom -- 12/16/2004, 8:39 am
Re: Offbeat question
pikabike -- 12/15/2004, 7:05 pm
Re: Offbeat question
Nick Schade - Guillemot Kayaks -- 12/16/2004, 9:27 am
graphite bottoms
LeeG -- 12/15/2004, 9:49 am
Re: graphite bottoms
Rob Macks -- 12/15/2004, 12:50 pm
Re: graphite bottoms
Dennis -- 12/15/2004, 1:03 pm
Re: graphite bottoms
Rob Macks -- 12/15/2004, 1:20 pm
Re: graphite bottoms
Randy Knauff -- 12/15/2004, 4:05 pm
Re: graphite bottoms
Robert N Pruden -- 12/16/2004, 11:26 am
Re: graphite bottoms
LeeG -- 12/15/2004, 7:10 pm
You are right about this to a point
Robert N Pruden -- 12/16/2004, 2:14 pm
Re: graphite bottoms
Rob Macks -- 12/15/2004, 4:55 pm
Hey Rob, where did you get that number from?
Robert N Pruden -- 12/16/2004, 2:07 pm
Re: Hey Rob, where did you get that number from? *LINK*
Glen Smith -- 12/16/2004, 3:28 pm
Excellent info, Glen, thanks.
Robert N Pruden -- 12/16/2004, 7:36 pm
Is this the same problem? *Pic*
John Caldeira -- 12/15/2004, 8:22 am
Re: Is this the same problem?
Kurt Loup, Baton Rouge -- 12/15/2004, 5:39 pm
Re: Is this the same problem?
Rob Macks -- 12/15/2004, 12:46 pm
Re: Is this the same problem?
Gordon Niessen -- 12/15/2004, 2:18 pm
Re: Is this the same problem?
Will -- 12/16/2004, 11:53 am
Re: Epoxy: Out of the Pit of Dispair
Jim Kozel -- 12/14/2004, 11:17 pm
Re: Epoxy: Out of the Pit of Dispair
Rob Macks -- 12/15/2004, 9:51 am
another story of support.
Rob B -- 12/15/2004, 12:17 am
Re: Epoxy: Out of the Pit of Dispair
CM Hair -- 12/14/2004, 9:42 pm
Re: Epoxy: Out of the Pit of Dispair
KenC -- 12/14/2004, 11:40 pm
Re: Thanks for sharing
pikabike -- 12/14/2004, 6:57 pm
Re: Thanks for sharing
Rob Macks -- 12/15/2004, 12:52 pm
Re: Thanks for sharing
Erik, Belgium -- 12/15/2004, 9:16 am
sorry
Erik, Belgium -- 12/15/2004, 5:24 pm
Re: Now *I'm* sorry.
pikabike -- 12/15/2004, 7:27 pm
Here ya go: from Rob Macks and Martin Step *LINK*
pikabike -- 12/15/2004, 7:16 pm
Here ya go: from Rob Macks and Martin Step
pikabike -- 12/15/2004, 7:15 pm