Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Tools: saber saw guide
By:Tom Yost
Date: 2/5/2008, 12:41 pm
In Response To: Re: Tools: saber saw guide (Terry Haines)

: Tom, cutting all those stringers with a saber saw must have been a trial. I
: understand that with a table saw your workshop has to be twice as long as
: the longest stringer if one is to do the job in a single pass, or the
: doors have to be open at both ends ... Brrrr.

Since there are only 6 - 10 stringers it's really no big deal. Probably about
60 - 90 minutes work with a jig saw.

: I use a hand (circular) saw with a thin kerf finish blade for cutting
: stringers. I built a narrow bench for cutting, it runs almost the full
: length of the workshop and has a top made of insulating foam; mine breaks
: up into sections for storing. Cost $40, time 3 hours.

Nice bench. You seem to have addressed safety concerns quite well.

I've ripped full length 3/16" and 1/4" strips for 7 woodstrip boats using
only a circular saw. I like the portability of the saw, as I tend to cut
only as many strips as I need for each day's session. Not as precise as
a table saw, but precise enough for me.

Time to get back to the bamboo stringers...using a band saw.

Regards,

Tom

Messages In This Thread

Tools: saber saw guide
Scott Shurlow -- 2/3/2008, 6:49 pm
Re: Tools: saber saw guide *LINK* *Pic*
Tom Yost -- 2/4/2008, 12:48 pm
Re: Tools: saber saw guide
Terry Haines -- 2/5/2008, 11:30 am
Re: Tools: saber saw guide
Tom Yost -- 2/5/2008, 12:41 pm
Re: Tools: saber saw guide
Terry Haines -- 2/5/2008, 11:43 pm
Re: Tools: saber saw guide
george jung -- 2/4/2008, 11:20 pm
Re: Tools: saber saw guide
Terry Haines -- 2/5/2008, 11:10 am
Re: Tools: saber saw guide *Pic*
Tom Yost -- 2/5/2008, 9:41 am
Re: Tools: saber saw guide
george jung -- 2/5/2008, 6:32 pm
Re: Tools: saber saw guide
Paul G. Jacobson -- 2/6/2008, 12:59 pm
Re: Tools: saber saw guide
Tom Yost -- 2/5/2008, 7:16 pm
modern materials, old designs
Paul G. Jacobson -- 2/5/2008, 2:36 am
Re: modern materials, old designs (2nd attempt) *Pic*
Tom Yost -- 2/5/2008, 10:13 am
Re: modern materials, old designs *Pic*
Tom Yost -- 2/5/2008, 10:07 am
Re: Tools: saber saw guide
Jay Babina -- 2/4/2008, 9:15 am
Re: Tools: saber saw guide
Scott Shurlow -- 2/5/2008, 7:35 am
Re: Tools: saber saw table *Pic*
Paul G. Jacobson -- 2/5/2008, 2:25 pm
Re: Tools: saber saw table
Scott Shurlow -- 2/6/2008, 7:22 am
here's what it looks like *Pic*
Paul G. Jacobson -- 2/7/2008, 11:56 am
Re: Tools: saber saw table
Paul G. Jacobson -- 2/6/2008, 12:17 pm
Re: Tools: saber saw table
dave -- 2/6/2008, 12:49 pm
Re: Tools: saber saw guide
Kudzu -- 2/5/2008, 9:18 am
Re: Tools: saber saw guide
Kudzu -- 2/4/2008, 9:29 am
Re: Tools: saber saw guide
Terry Haines -- 2/4/2008, 11:58 am
Re: Tools: saber saw guide
Bill Hamm -- 2/6/2008, 2:13 am
Re: Tools: saber saw guide
Terry Haines -- 2/8/2008, 6:36 pm
Re: Tools: saber saw guide
Bill Hamm -- 2/10/2008, 3:06 am
Re: Tools: saber saw guide *LINK*
Kudzu -- 2/9/2008, 7:06 pm
Re: Tools: saber saw guide
Terry Haines -- 2/10/2008, 10:18 am
Re: Tools: saber saw guide
David Kennedy -- 2/4/2008, 12:16 pm
Re: Tools: saber saw guide
John D. -- 2/4/2008, 2:02 am
Re: Tools: saber saw guide
Scott Shurlow -- 2/4/2008, 7:28 am
Re: Tools: saber saw guide
Paul G. Jacobson -- 2/3/2008, 8:56 pm