Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Greater Penetration
By:Chip Sandresky
Date: 2/1/2002, 12:45 pm
In Response To: Only 1/32" Penetration ???..... (Joe)

See Wooden Boat Magazine Issue #160 May/June 2001. I was just looking at it this morning. Robb White builds remarkably strong/light boats by effectively reversing the outgassing effect in curing epoxy. He heats his shop to 130F degrees until the boat is that temperature. Then switches on the Air Conditioner and starts applying epoxy. The article says he throws as much on as the wood will accept... cross sections of the treated wood look like they've been vacuum-bagged.

I would never go to that extreme... but would love to own a boat built that way.

- Chip

Chip's Web Site

Messages In This Thread

Epoxy: To Evaporate and Blush or not to .....
Joe -- 1/30/2002, 8:20 pm
Re: Epoxy: To Evaporate and Blush or not to .....
Steve Smith -- 2/1/2002, 4:38 pm
Thank you Mr. Smith
Pete Rudie -- 2/1/2002, 5:52 pm
Re: Epoxy: To Evaporate and Blush or not to .....
Jim Chowning -- 2/1/2002, 10:40 am
Thanks for the answer
Pete Rudie -- 2/1/2002, 12:09 pm
Re: Thanks for the answer
Jim Chowning/The Rot doctor -- 2/1/2002, 12:55 pm
Re: Thanks for the answer
LeeG -- 2/1/2002, 1:41 pm
Re: Thanks for the answer
Jim Chowning/The Rot doctor -- 2/2/2002, 12:31 pm
Re: Thanks for the answer *Pic*
Pete Rudie -- 2/2/2002, 1:46 pm
Re: Epoxy: To Evaporate and Blush or not to .....
Severne -- 1/31/2002, 11:52 am
Just when things looked clear...
Pete Rudie -- 1/31/2002, 9:31 pm
Re: Just when things looked clear...
Joe -- 2/1/2002, 3:01 am
Re: you are a reasonable guy
LeeG -- 1/31/2002, 10:52 pm
Only 1/32" Penetration ???.....
Joe -- 1/31/2002, 2:40 pm
Re: Greater Penetration
Chip Sandresky -- 2/1/2002, 12:45 pm
Re: Only 1/32" Penetration ???.....
Pete Rudie -- 1/31/2002, 2:56 pm
Re: Only 1/32" Penetration ???.....
Nick Schade - Guillemot Kayaks -- 2/1/2002, 10:54 am
Good point. And it IS Softwood. *NM*
Joe -- 2/1/2002, 11:11 am
however
mike allen ---> -- 1/31/2002, 3:05 pm
Re: however
Jim Chowning/The Rot doctor -- 2/1/2002, 7:36 pm
Re: however
Pete Rudie -- 1/31/2002, 6:22 pm
Re: however
mike allen ---> -- 1/31/2002, 6:38 pm
I asked Dr.Rot to come and answer us HERE!
Joe -- 1/31/2002, 4:45 pm
Re: I asked Dr.Rot to come and answer us HERE!
Nick Schade - Guillemot Kayaks -- 2/1/2002, 10:49 am
Re: Only 1/32" Penetration ???.....
LeeG -- 1/31/2002, 3:01 pm
It's not really blush .....
Pete Rudie -- 1/31/2002, 1:40 am
But could it be . . .
Paul G. Jacobson -- 1/31/2002, 10:33 pm
Good point,
Pete Rudie -- 1/31/2002, 11:50 pm
MORE than fair. Thanks *NM*
Joe -- 1/31/2002, 7:31 pm
Re: It's not really blush .....
Joe -- 1/31/2002, 3:04 am
Re: It's not really blush .....
LeeG -- 1/31/2002, 3:27 am
Re: Pure Speculation...
Nick Schade - Guillemot Kayaks -- 1/31/2002, 9:02 am
Re: Pure Speculation...
Tom Johansen -- 1/31/2002, 5:53 pm
Re: Pure Speculation...
LeeG -- 1/31/2002, 8:31 pm
Re: Pure Speculation...
Jim Chowning/The Rot doctor -- 2/1/2002, 2:01 pm
Re: Pure Speculation...
LeeG -- 2/1/2002, 5:17 pm
No speculation here...
Pete Rudie -- 1/31/2002, 6:15 pm
Dr. Rot replies ....
Joe -- 1/31/2002, 7:01 pm
Re: immaculate speculation
LeeG -- 1/31/2002, 2:56 pm
Limitations
Pete Rudie -- 1/31/2002, 11:21 am
Re: Limitations
Jim Chowning/The Rot doctor -- 2/1/2002, 1:49 pm
Re: Limitations
Nick Schade - Guillemot Kayaks -- 1/31/2002, 12:59 pm
Re: More Speculation...
Shawn Baker -- 1/31/2002, 10:46 am
Solving solvent worries
Paul G. Jacobson -- 1/30/2002, 10:50 pm
Re: Solving solvent worries
Joe -- 1/31/2002, 1:12 am
Re: Solving solvent worries
Jim Chowning/The Rot doctor -- 2/1/2002, 1:16 pm
Re: Epoxy: To Evaporate and Blush or not to .....
LeeG -- 1/30/2002, 8:54 pm
Re: Epoxy: To Evaporate and Blush or not to .....
Joe -- 1/30/2002, 10:13 pm
Re: Epoxy: To Evaporate and Blush or not to .....
LeeG -- 1/30/2002, 11:17 pm
Re: Epoxy: Good questions
don -- 1/30/2002, 10:48 pm
Re: Epoxy: To Evaporate and Blush or not to .....
Jon Murray -- 1/30/2002, 10:35 pm