Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Shop: Cutting Plywood - HELP!
By:Grant G
Date: 3/8/2002, 1:06 pm
In Response To: Shop: Cutting Plywood - HELP! (Patsy)

I have a B & D Combo so the jigsaw portion is the most basic you can get, yet it still cuts well.

1. Don't force it. The saw will cut by itself with only the minimum of pressure from the operator. I found if I got too "eager" it jumped around.

2. Keep the foot flat. This means making sure the ply is also flat. If it does start to jump - back off, flatten the foot and start cutting again.

3. Support the area your in front of your cutting as well as where you have cut. Because of the support needed, long panels are better and faster cut with a hand saw. You can still cut a fair a mount of curve with them.

4. Use a plywood blade. It makes all the difference to tearout.

5. Some ply are just jigsaw unfriendly. Used what was known as "Redwood" ply in NZ for my cockpit coamings and found that the top layer of veneer would split off for a good 5cm. I got around it by cutting the 1st layer with a knife then sawing 5mm on the outside of the line.

Messages In This Thread

Shop: Cutting Plywood - HELP!
Patsy -- 3/8/2002, 7:47 am
Re: Shop: Cutting Plywood - HELP!
jim kozel -- 3/8/2002, 11:05 pm
Bosch jig saws and Multi-Masters ROOL!
Brian Nystrom -- 3/11/2002, 1:03 pm
Re: Shop: Cutting Plywood - HELP!
Patsy -- 3/9/2002, 7:48 am
Re: Shop: Japan Woodworker Has Good Prices
Chip Sandresky -- 3/11/2002, 12:23 pm
Re: Shop: Cutting Plywood - HELP!
Don Beale -- 3/9/2002, 12:18 pm
Re: Shop: Cutting Plywood - HELP!
daren neufeld -- 3/9/2002, 9:53 am
Re: Shop: Cutting Plywood - HELP!
Charles Cooper -- 3/10/2002, 10:34 pm
Re: Shop: Cutting Plywood - HELP! *Pic*
John Monfoe -- 3/9/2002, 9:39 am
Re: Shop: Cutting Plywood - HELP!
Brian Nystrom -- 3/11/2002, 1:07 pm
Re: Shop: Cutting Plywood - HELP!
Richard Boyle -- 3/9/2002, 9:16 am
Re: Shop: Cutting Plywood - HELP!
Greg Morse -- 3/9/2002, 9:13 am
Re: Shop: Cutting Plywood - HELP!
daren neufeld -- 3/8/2002, 9:29 pm
Re: Shop: A tool-a-holics confession
Brent Curtis -- 3/8/2002, 10:36 pm
Re: Shop: A tool-a-holics confession
Patsy -- 3/9/2002, 7:45 am
Don't cheat yourself!
Brian Nystrom -- 3/11/2002, 12:56 pm
Re: Shop: A tool-a-holics confession
Robert Palmeter -- 3/9/2002, 4:26 pm
Re: Shop: A tool-a-holics confession
daren neufeld -- 3/8/2002, 10:55 pm
Anti splinter plate?
Brian Nystrom -- 3/8/2002, 3:39 pm
Re: Anti splinter plate?
Greg Morse -- 3/8/2002, 11:29 pm
Re: Anti splinter plate?
Brian Nystrom -- 3/11/2002, 12:49 pm
Re: Anti splinter plate?
Dick L. -- 3/8/2002, 9:08 pm
Re: Anti splinter plate?
Brian Nystrom -- 3/11/2002, 12:47 pm
Re: Anti splinter plate?
John Schroeder -- 3/8/2002, 9:05 pm
Re: Shop: Cutting Plywood - HELP!
Grant G -- 3/8/2002, 1:06 pm
Re: Shop: Cutting Plywood - HELP! *Pic*
Chip Sandresky -- 3/8/2002, 12:45 pm
Re: Shop: Cutting Plywood - HELP!
Ross Sieber -- 3/8/2002, 11:21 am
Re: Shop: Cutting Plywood - HELP!
Eric -- 3/8/2002, 9:38 am
Re: Shop: Cutting Plywood - HELP!
James Neely -- 3/8/2002, 11:13 am
knife blade for jigsaw??
mike allen ---> -- 3/8/2002, 2:35 pm
Re: knife blade for jigsaw??
Paul G. Jacobson -- 3/8/2002, 7:52 pm
Heck No! Use a "Stanley Knife"
James Neely -- 3/8/2002, 5:06 pm
Re: Shop: Cutting Plywood - HELP!
Phil -- 3/8/2002, 9:34 am
Re: Shop: Cutting Plywood - HELP!
Rob Macks -- 3/8/2002, 9:33 am
Re: Shop: Cutting Plywood - HELP!
Rehd -- 3/8/2002, 9:25 am
Re: Shop: Cutting Plywood - HELP!
leo s -- 3/8/2002, 8:54 am
Re: Shop: Cutting Plywood - HELP!
KenC -- 3/8/2002, 8:20 am
Re: packing tape and planes
Dave Houser -- 3/8/2002, 3:58 pm
Re: Shop: Cutting Plywood - HELP!
Elliott -- 3/8/2002, 8:03 am