Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Anti splinter plate?
By:Brian Nystrom
Date: 3/8/2002, 3:39 pm
In Response To: Shop: Cutting Plywood - HELP! (Patsy)

As others have said, good support, the right blade, using a guide and firm downward pressure on the saw will help a lot. However, the better saws - like the Bosch - also have anti-splinter plates that snap into the sole and fit very close to the blade. Perhaps you could make such a plate that could be attached to your saw's sole plate with double-sided tape. Plastic, wood or anything similar and 1/8"-1/4" thick should work. Here's an idea of how it could be done:

1) Cut a piece of material to the size of the sole plate.

2) Mark a line down the center, then use your jig saw to cut a slot in the plate.

3) Slip the plate onto the base from behind, so that the slot faces forward and the blade is in the slot. Mark the location of the front of the blade.

4) Remove the plate and cut away some of the material from in front of the blade, so you can see your cut line as you work.

5) Apply double sided tape and attach the plate to the sole of your saw. Put the side with the smoothest cut suface downward, to give maximum support to the workpiece.

6) Go cut some plywood.

Happy sawing!

Brian

Messages In This Thread

Shop: Cutting Plywood - HELP!
Patsy -- 3/8/2002, 7:47 am
Re: Shop: Cutting Plywood - HELP!
jim kozel -- 3/8/2002, 11:05 pm
Bosch jig saws and Multi-Masters ROOL!
Brian Nystrom -- 3/11/2002, 1:03 pm
Re: Shop: Cutting Plywood - HELP!
Patsy -- 3/9/2002, 7:48 am
Re: Shop: Japan Woodworker Has Good Prices
Chip Sandresky -- 3/11/2002, 12:23 pm
Re: Shop: Cutting Plywood - HELP!
Don Beale -- 3/9/2002, 12:18 pm
Re: Shop: Cutting Plywood - HELP!
daren neufeld -- 3/9/2002, 9:53 am
Re: Shop: Cutting Plywood - HELP!
Charles Cooper -- 3/10/2002, 10:34 pm
Re: Shop: Cutting Plywood - HELP! *Pic*
John Monfoe -- 3/9/2002, 9:39 am
Re: Shop: Cutting Plywood - HELP!
Brian Nystrom -- 3/11/2002, 1:07 pm
Re: Shop: Cutting Plywood - HELP!
Richard Boyle -- 3/9/2002, 9:16 am
Re: Shop: Cutting Plywood - HELP!
Greg Morse -- 3/9/2002, 9:13 am
Re: Shop: Cutting Plywood - HELP!
daren neufeld -- 3/8/2002, 9:29 pm
Re: Shop: A tool-a-holics confession
Brent Curtis -- 3/8/2002, 10:36 pm
Re: Shop: A tool-a-holics confession
Patsy -- 3/9/2002, 7:45 am
Don't cheat yourself!
Brian Nystrom -- 3/11/2002, 12:56 pm
Re: Shop: A tool-a-holics confession
Robert Palmeter -- 3/9/2002, 4:26 pm
Re: Shop: A tool-a-holics confession
daren neufeld -- 3/8/2002, 10:55 pm
Anti splinter plate?
Brian Nystrom -- 3/8/2002, 3:39 pm
Re: Anti splinter plate?
Greg Morse -- 3/8/2002, 11:29 pm
Re: Anti splinter plate?
Brian Nystrom -- 3/11/2002, 12:49 pm
Re: Anti splinter plate?
Dick L. -- 3/8/2002, 9:08 pm
Re: Anti splinter plate?
Brian Nystrom -- 3/11/2002, 12:47 pm
Re: Anti splinter plate?
John Schroeder -- 3/8/2002, 9:05 pm
Re: Shop: Cutting Plywood - HELP!
Grant G -- 3/8/2002, 1:06 pm
Re: Shop: Cutting Plywood - HELP! *Pic*
Chip Sandresky -- 3/8/2002, 12:45 pm
Re: Shop: Cutting Plywood - HELP!
Ross Sieber -- 3/8/2002, 11:21 am
Re: Shop: Cutting Plywood - HELP!
Eric -- 3/8/2002, 9:38 am
Re: Shop: Cutting Plywood - HELP!
James Neely -- 3/8/2002, 11:13 am
knife blade for jigsaw??
mike allen ---> -- 3/8/2002, 2:35 pm
Re: knife blade for jigsaw??
Paul G. Jacobson -- 3/8/2002, 7:52 pm
Heck No! Use a "Stanley Knife"
James Neely -- 3/8/2002, 5:06 pm
Re: Shop: Cutting Plywood - HELP!
Phil -- 3/8/2002, 9:34 am
Re: Shop: Cutting Plywood - HELP!
Rob Macks -- 3/8/2002, 9:33 am
Re: Shop: Cutting Plywood - HELP!
Rehd -- 3/8/2002, 9:25 am
Re: Shop: Cutting Plywood - HELP!
leo s -- 3/8/2002, 8:54 am
Re: Shop: Cutting Plywood - HELP!
KenC -- 3/8/2002, 8:20 am
Re: packing tape and planes
Dave Houser -- 3/8/2002, 3:58 pm
Re: Shop: Cutting Plywood - HELP!
Elliott -- 3/8/2002, 8:03 am