Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: S&G: Vacuum relief
By:Scott Baxter
Date: 8/18/2002, 9:38 pm
In Response To: Re: S&G: Vacuum relief (Ross Hendry)

You can drill a hole near the top of the bulkhead just smaller than a piece of aquarium pump tubing. Cut about twenty inches of tubbing and push it through the hole (it will seal just fine) until ten inches is on either side of the bulkhead. Fasten it near the bottom of the bulkhead on both sides of the bulkhead (if you want to get fancy fasten one end on the left of the boat and the other on the right of the boat). (You can go from bottom to top if you prefer.) Even in a capsize the bottom of the boat usually has an airspace so the tubbing will be above the water. This should make it so you only get about one squirt gun squirt of water in the dry area.

Messages In This Thread

S&G: Vacuum relief
Rod -- 8/16/2002, 11:03 pm
Holes are good
Brian Nystrom -- 8/19/2002, 1:18 pm
Thanks all- holes it is! *NM*
Rod -- 8/20/2002, 7:03 am
Thanks, Brian. *NM*
Joe -- 8/19/2002, 8:55 pm
Re: S&G: Vacuum relief
Ross Hendry -- 8/18/2002, 4:21 am
Re: S&G: Vacuum relief
Scott Baxter -- 8/18/2002, 9:38 pm
This mouse trap is TOO good. *NM*
Tony -- 8/19/2002, 6:25 pm
I 2nd that: Award for cleverest Solution *NM*
Joe -- 8/19/2002, 8:58 pm
Re: S&G: Vacuum relief
Emmett -- 8/17/2002, 9:09 pm
Re: Artic Tern 14
Don -- 8/17/2002, 2:43 pm
Re: Artic Tern 14
Joe -- 8/17/2002, 11:01 pm
Plan to get wet.
Jason -- 8/18/2002, 11:13 am
Re: Artic Tern 14
Emmett -- 8/18/2002, 1:06 am
Re: Artic Tern 14
Greg Morse -- 8/18/2002, 10:06 am
Re: Artic Tern 14
Emmett -- 8/18/2002, 1:34 pm
Re: Artic Tern 14
Greg Morse -- 8/18/2002, 1:50 pm
Re: Artic Tern 14
Emmett -- 8/18/2002, 6:45 pm
Re: Artic Tern 14
Joe -- 8/18/2002, 2:02 am
Hole location
Brian Nystrom -- 8/19/2002, 1:13 pm
Relief is as near as a bottle of wine
Paul G. Jacobson -- 8/17/2002, 12:28 am
Re: S&G: Vacuum relief
Sam McFadden -- 8/17/2002, 12:05 am
Re: S&G: Vacuum relief
Joe -- 8/17/2002, 2:27 am
Big hole with a small hole inside a cork
Paul G. Jacobson -- 8/20/2002, 1:03 am
Don't you ever...
Brian Nystrom -- 8/20/2002, 12:41 pm
Interesting idea for a survey :) responses please
Paul G. Jacobson -- 8/21/2002, 12:35 am
Re: Interesting idea for a survey :) responses ple
Shawn Baker -- 8/23/2002, 1:32 pm
Re: Interesting idea for a survey :) responses ple
Jack Sanderson -- 8/22/2002, 10:55 am
Re: Interesting idea for a survey :) responses ple
Joe -- 8/22/2002, 1:05 pm
dessicants
Paul G. Jacobson -- 8/23/2002, 1:10 am
Re: dessicants
G.V.Prabhu -- 11/19/2003, 3:56 am
Re: Interesting idea for a survey :) responses ple
Brian Nystrom -- 8/21/2002, 12:29 pm
Re: Interesting idea for a survey :) responses ple
Ben Staley -- 8/21/2002, 10:12 am
Re: Interesting idea for a survey :) responses ple
John Waddington -- 8/21/2002, 7:20 am
Re: Don't you ever...
Joe -- 8/20/2002, 2:51 pm
Re: S&G: Vacuum relief
Pamela -- 8/17/2002, 10:41 am
Re: S&G: Vacuum relief
Robert -- 8/17/2002, 9:26 am
Re: S&G: Vacuum relief
Brian Nystrom -- 8/19/2002, 1:05 pm