Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: What Myrl and Ross said
By:Shawn Baker
Date: 1/7/2003, 5:24 pm
In Response To: Re: Strip: cockpit coaming (Myrl Tanton)

I do much the same as Myrl and Ross have described.

As Ross said, overlapping the glass is strong enough--I lift and carry my kayak by the coaming lip, and I'm not easy on boats while paddling, either (boat over boat rescues in rough water is about as tough as you can be on a kayak).

Unlike Myrl, I do glass my coaming lips (maple/mahogany). Probably not necessary for strength, I like it for waterproofness. Epoxy will eventually wear away, but glass is there to stay--even with abuse.

Shawn

: I've build one whole kayak, and did somthing very simillar to the method as
: described by Ross. It worked well for me.

: My sequence ignoring most sanding and the like: 1) glassed only the outside
: of the deck with the recess.

: 2) Sand around the edge of the glassed recess now so fillet later will have a
: good mechanical bond

: 3) built the combing risers, as per Nicks book.

: 4) Fillet Glassed the Combing riser out side edge. My strips were not as
: biased as I'd liked, they were left overs... I used three pieces to make a
: single layer that went from the combing lip to about one inch past the
: outside edge of the recess.

: 5) While glassing the inside of the deck, I used two pieces which overlapped
: the entire cockpit area. I slit the insided of the cockpit, and folded the
: fiberglass over the in side of the combing risers. The Fiberglass will
: seperate at the point of the slit, however the fiberglass will not bend
: nicely without a slit up the side in places, I ensured these slits did not
: overlap, this prevents any area from having not glass. I found I needed
: more slits in the glass than expected to get it to transition over the
: insided of the combing riser. It may be worth while to not do this and
: used bias cut pieces of glass, which would require fewer cuts. (I think
: these slits in the glass are called darts).

: 6) I build up the combing lip using strips of ash, I was going to put
: fiberglass on these, but decided it was strong enough with 3 layers of
: epoxy on them.

: I weigh 190 lbs, and sit on the lip to get in and out of the kayak It seems
: really strong. However it has not seen much use yet.

: hope this helps

: Myrl

Messages In This Thread

Strip: cockpit coaming
Les -- 1/6/2003, 9:12 pm
Re: Strip: cockpit coaming
KenC -- 1/7/2003, 11:06 pm
Re: Strip: cockpit coaming
Rick Allnutt -- 1/7/2003, 9:21 pm
Re: Strip: cockpit coaming
Chip Sandresky -- 1/7/2003, 12:34 pm
Re: filletting the coaming riser
Shawn Baker -- 1/7/2003, 5:39 pm
Re: Strip: cockpit coaming *LINK* *Pic*
Charles Leach -- 1/7/2003, 11:22 am
Re: Strip: cockpit coaming
Shawn Baker -- 1/7/2003, 5:36 pm
Re: Strip: cockpit coaming *LINK*
Charles Leach -- 1/7/2003, 7:14 pm
Re: Strip: cockpit coaming
Ross Leidy -- 1/6/2003, 11:38 pm
Re: Strip: cockpit coaming
Myrl Tanton -- 1/7/2003, 12:43 pm
Re: What Myrl and Ross said
Shawn Baker -- 1/7/2003, 5:24 pm