Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: trouble with b&c routing
By:Tim Eastman
Date: 2/6/2003, 1:04 pm
In Response To: Re: Strip: trouble with b&c routing *Pic* (Chip Sandresky)

Chip,

Do you have a link or maybe even a description of how you built your table? If so maybe you can send that off-list to my e-mail address. That zero clearance option sounds tempting.

Thanks
Tim Eastman

(snip)
: The fence would normally straddle the bit but I have it moved back for the
: picture. One of the other builders also had an idea to use a zero
: clearance fence which could be cool. I would get the height set and then
: slowly move the fence into the bit to let it make its own opening.

Messages In This Thread

Strip: trouble with b&c routing
Pascal, in Chile -- 2/6/2003, 10:21 am
Re: Strip: trouble with b&c routing
David Hanson -- 2/6/2003, 4:40 pm
b&c vs bevel
mike allen -- 2/7/2003, 9:13 pm
Re: Strip: trouble with b&c routing
Mike Loriz -- 2/6/2003, 3:12 pm
Re: Strip: trouble with b&c routing *LINK* *Pic*
Kurt Loup, Baton Rouge -- 2/6/2003, 1:49 pm
Thanks everyone, this ought to work ... *LINK*
Pascal, in Chile -- 2/6/2003, 3:30 pm
Re: Thanks everyone, this ought to work ...
Kurt Loup, Baton Rouge -- 2/6/2003, 4:49 pm
Re: Strip: trouble with b&c routing
Paul J -- 2/6/2003, 1:40 pm
Re: Strip: trouble with b&c routing *Pic*
Chip Sandresky -- 2/6/2003, 12:18 pm
Re: Strip: trouble with b&c routing
Tim Eastman -- 2/6/2003, 1:04 pm
Re: Strip: trouble with b&c routing
Chip Sandresky -- 2/6/2003, 2:16 pm
Re: Strip: trouble with b&c routing
Kent LeBoutillier -- 2/6/2003, 11:39 am
Re: Strip: trouble with b&c routing
Tim Eastman -- 2/6/2003, 12:56 pm
Re: Strip: trouble with b&c routing
Kent LeBoutillier -- 2/7/2003, 6:22 am
My turn for a stupid question....
Bob Deutsch -- 2/7/2003, 12:06 pm
Re: My turn for a stupid question....
Kent LeBoutillier -- 2/7/2003, 9:42 pm
If I might explain beveling
Paul G. Jacobson -- 2/7/2003, 12:20 am
Re: If I might explain beveling
Bob Deutsch -- 2/7/2003, 4:29 am
Re: If I might explain beveling
Jack Sanderson -- 2/7/2003, 10:31 am
Thanks Sam & Jack! *NM*
Bob Deutsch -- 2/7/2003, 12:08 pm
Re: If I might explain beveling
Sam McFadden -- 2/7/2003, 10:30 am
Re: If I might explain beveling
Mike Loriz -- 2/7/2003, 7:57 pm
Re: If I might explain beveling
Sam McFadden -- 2/7/2003, 11:17 pm
Re: If I might explain beveling
Mark Normand -- 2/7/2003, 7:11 am
I second Tim's question...thanks Kent... *NM*
Bob Deutsch -- 2/6/2003, 3:19 pm
Re: I second Tim's question...thanks Kent...
Don Lucas -- 2/7/2003, 9:28 am