Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Tools: I'll wack the hornet's nest!
By:Todd Sullivan
Date: 3/23/2008, 10:32 am
In Response To: Re: Tools: I'll wack the hornet's nest! (Jay Babina)

: I tend to agree and I think a lot of people use a plane to remove the high
: spots as well as glue residue for several reasons. 1. you don't need
: electricty. 2. a plane set very fine - running with the strips does a nice
: job or removing the strip edges. 3. no saw dust 4. It an enjoyable tool to
: use 5. cutting away glue works better than sanding it.

: In a model making or tool making shop you would be fired using a flat sander
: on a rounded surface. Everything is sanded with flexible, long sanding
: boards. I've been to commercial kayak manufacturers and all sanding of the
: plugs is with long flexible sanding boards.

: Robs method is totally valid and the proof is in the outcome - Rob make
: beautiful boats. And his point of not flattening out the surfaces is
: correct. But I think nipping off high spots with a fine plane works well
: and I'll bet most people do that and switch to sanding once that's done.

I've no doubt I'd be fired in a heartbeat for some of my methods! But until then...

I guess I pretty much treat the belt sander like a plane. It's a fluid process. The sander is never ever at rest in one spot, I apply very little pressure and run at a slight diagonal, which for some reason gives me confidence the I'm not dig-in an edge of the belt.

I've little doubt the ROS and long-board perform better work. Been a while since procuring any new tools, I'll take ET's advice and go shopping. Particularly if the ROS will help smoothing out my fill-coats.

Regarding my dinky thumb-nail plane. It did better (for me) in taking off glue spots than my larger planes. Mostly, because it's so small that you can actually see what your planing (and not planing) as you do it. With the larger planes, you don't actually know what your taking off until after you've made the pass. The little plane did it's best work doing the bead/cove work on the random ends. It was a pretty handy little tool.

Todd

Messages In This Thread

Tools: I'll wack the hornet's nest!
Rob Macks / Laughing Loon CC&K -- 3/21/2008, 1:51 pm
Re: Tools: I'll wack the hornet's nest!
Acors -- 3/25/2008, 3:14 am
Re: Tools: Waterboarding and ....
Rob Macks / Laughing Loon CC&K -- 3/25/2008, 2:24 pm
Re: Tools: Waterboarding and ....
Bill Hamm -- 3/26/2008, 1:14 am
Re: Tools: Waterboarding and ....
Mike Bielski -- 3/25/2008, 6:25 pm
Re: Tools: Waterboarding and ....
Glen Smith -- 3/25/2008, 4:05 pm
Re: Tools: Waterboarding and ....
Rob Macks / Laughing Loon CC&K -- 3/25/2008, 5:42 pm
Re: Tools: Waterboarding and ....
PatrickC -- 4/1/2008, 10:01 am
Re: Tools: Waterboarding and ....
Rob Macks / Laughing Loon CC&K -- 4/2/2008, 7:33 pm
:)
kelly t -- 4/2/2008, 9:15 pm
Re: :) :) :) (:
Rob Macks / Laughing Loon CC&K -- 4/3/2008, 8:01 am
Re: Tools: I'll wack the hornet's nest!
Mike Bielski -- 3/25/2008, 11:22 am
Re: Tools: I'll wack the hornet's nest!
Todd Sullivan -- 3/25/2008, 9:32 pm
Re: Tools: I'll wack the hornet's nest!------WebKi
Jay Babina------WebKitFormBoundaryAF6vd4C7eld+PENR -- 3/25/2008, 8:51 am
Re: Tools: I'll wack the hornet's nest!
Mike Bielski -- 3/23/2008, 12:35 pm
Re: Tools: I'll wack the hornet's nest!
Bill Hamm -- 3/24/2008, 1:33 am
Re: Tools: I'll wack the hornet's nest!
Dan Caouette (CSFW) -- 3/24/2008, 11:40 am
Re: Tools: I'll wack the hornet's nest!
Rob Macks / Laughing Loon CC&K -- 3/24/2008, 8:29 am
Re: Tools: I'll wack the hornet's nest!
Bill Hamm -- 3/25/2008, 1:22 am
Re: Tools: I'll wack the hornet's nest!
Rob Macks / Laughing Loon CC&K -- 3/25/2008, 2:41 pm
Re: Tools: I'll wack the hornet's nest!
Mike Bielski -- 3/25/2008, 6:06 pm
Sanding is Skill Free?
Nick Schade - Guillemot Kayaks -- 3/25/2008, 5:59 pm
Re: Sanding is Skill Free?
Rob Macks / Laughing Loon CC&K -- 3/25/2008, 10:54 pm
Re: Tools: I'll wack the hornet's nest!
Mike Savage -- 3/24/2008, 10:01 am
Re: Tools: I'll wack the hornet's nest!
Rob Macks / Laughing Loon CC&K -- 3/23/2008, 5:47 pm
Re: Tools: I'll wack the hornet's nest!
Rob Macks / Laughing Loon CC&K -- 3/23/2008, 4:03 pm
Re: Tools: I'll wack the hornet's nest!
Mike Savage -- 3/23/2008, 12:57 pm
Glue
Todd Sullivan -- 3/23/2008, 9:06 pm
Re: Glue
Mike Bielski -- 3/24/2008, 12:06 pm
Re: Glue
Todd Sullivan -- 3/24/2008, 9:48 pm
Re: Glue------WebKitFormBoundaryVBozkArD+XRe82MN
Mike Bielski------WebKitFormBoundaryVBozkArD+XRe82 -- 3/25/2008, 11:15 am
Re: Glue
Bill Hamm -- 3/25/2008, 1:18 am
Re: Glue *Pic*
Etienne Muller -- 3/24/2008, 11:21 am
Re: Glue
Dan Caouette (CSFW) -- 3/24/2008, 11:26 am
Re: No access...
Björn Thomasson -- 3/25/2008, 12:30 pm
Re: No access... *LINK*
Dan Caouette (CSFW) -- 3/25/2008, 1:18 pm
Re: No access...
Björn Thomasson -- 3/26/2008, 4:21 pm
Re: No access... *LINK*
Glen Smith -- 3/25/2008, 12:48 pm
Re: Glue
Etienne Muller -- 3/24/2008, 11:38 am
Re: Glue
Rob Macks / Laughing Loon CC&K -- 3/24/2008, 12:48 pm
Re: Glue
Etienne Muller -- 3/24/2008, 2:02 pm
Re: Glue
Mike Savage -- 3/24/2008, 9:16 pm
Re: Glue------WebKitFormBoundaryAJKY9jM9qs+BHftt
Dan Caouette (CSFW)------WebKitFormBoundaryAJKY9jM -- 3/24/2008, 11:47 am
Re: Glue
Rob Macks / Laughing Loon CC&K -- 3/24/2008, 8:34 am
Re: Glue
Mike Savage -- 3/24/2008, 6:47 am
Re: Tools: I'll wack the hornet's nest!
C.W. -- 3/22/2008, 8:51 pm
Re: Stung,
Paul Sylvester -- 3/23/2008, 7:00 am
Re: Tools: I'll wack the hornet's nest! *NM*
C.W. -- 3/22/2008, 8:26 pm
Still waiting for Spring to come?
Mike Scarborough -- 3/22/2008, 9:22 am
Re: Still waiting for Spring to come?
Etienne Muller -- 3/23/2008, 7:44 am
Re: Still waiting for Spring to come?
Doug Smith -- 3/22/2008, 3:38 pm
Re: Good Advice *LINK*
Pawistik -- 3/22/2008, 12:40 pm
Re: Tools: I'll wack the hornet's nest!
Rob Macks / Laughing Loon CC&K -- 3/21/2008, 2:13 pm
Re: Tools: I'll wack the hornet's nest!
Todd Sullivan -- 3/21/2008, 7:10 pm
Re: Tools: I'll wack the hornet's nest!
Jay Babina -- 3/23/2008, 7:41 am
Re: Tools: I'll wack the hornet's nest! *NM* *LINK*
Barry -- 3/29/2008, 6:54 am
Re: Tools: I'll wack the hornet's nest!
Todd Sullivan -- 3/23/2008, 10:32 am
Re: Tools: I'll wack the hornet's nest!
Mike Savage -- 3/23/2008, 7:59 am
Re: Tools: I'll wack the hornet's nest!
Etienne Muller -- 3/23/2008, 7:29 am
Re: Tools: I'll wack the hornet's nest!
Todd Sullivan -- 3/23/2008, 9:15 pm