Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Urethane Safety Issues
By:Bill Hamm
Date: 4/30/2008, 1:14 am
In Response To: Re: Urethane Safety Issues (Steve Rasmussen)

: I too know people that have had severe side effects from prolonged exposure
: to dust & fumes. It's a good motivator to pay attention.

: The hose takes some getting used to, but workable. I ended up dumping one
: batch of finish on the floor by snagging it with the hose. Lesson is keep
: your path clear. I suspended the King from the ceiling and stepped under
: it as I put on the finish.

: I used a foam brush so there were no issues with overspray foggin up the
: lense. It came with peel-off covers to deal with overspray. They tended to
: distort the view so I didn't use them.

: The blower is a bit noisy, but no worse than any other power tool. It is
: important to consider where you place it to make sure you are getting
: fresh air blown in.

: Steve

Good friend of mine isn't with us anymore from the results of overspray. He knew better too, was a shop teacher. Of course he was spraying a linear polyurethane system, bad thing to breath in.

Bill H.

Messages In This Thread

Material: hBN Coating Abrasion Test *LINK*
Dan Caouette (CSFW) -- 4/29/2008, 8:25 am
Re: Material: hBN Coating Abrasion Test
Acors -- 5/9/2008, 5:11 pm
Re: Material: hBN Coating Abrasion Test------WebKi
Dan Caouette (CSFW------WebKitFormBoundaryHAvdf7mj -- 5/12/2008, 8:21 am
Re: Material: hBN Coating Abrasion Test
Bill Hamm -- 4/30/2008, 1:05 am
Re: Material: hBN Coating Abrasion Test
Robert N Pruden -- 5/2/2008, 1:50 pm
Re: Material: hBN Coating Abrasion Test
Dan Caouette (CSFW) -- 4/30/2008, 10:17 am
Urethane Safety Issues
Ted Henry -- 4/29/2008, 4:57 pm
Re: Urethane Safety Issues
Roy -- 5/7/2008, 11:05 am
Re: Urethane Safety Issues
Roy -- 5/4/2008, 11:06 am
Re: Urethane Safety Issues
Bill Hamm -- 5/5/2008, 2:10 am
Ditto to what Bill said...------WebKitFormBoundary
Dan Caouette (CSFW)------WebKitFormBoundarydta+Yzz -- 5/5/2008, 9:00 am
Re: Urethane Safety Issues
Roy -- 5/5/2008, 5:58 am
Re: Urethane Safety Issues
Dan Caouette (CSFW) -- 4/30/2008, 10:02 am
Re: Urethane Safety Issues
Dan Caouette (CSFW) -- 4/30/2008, 10:06 am
Part III
Dan Caouette (CSFW) -- 4/30/2008, 10:06 am
Part II
Dan Caouette (CSFW) -- 4/30/2008, 10:04 am
Re: Urethane Safety Issues Part 1
Dan Caouette (CSFW) -- 4/30/2008, 10:03 am
Re: Urethane Safety Issues
Steve Rasmussen -- 4/29/2008, 5:21 pm
Re: Urethane Safety Issues
Bill Hamm -- 4/30/2008, 1:11 am
Re: Urethane Safety Issues
Steve Rasmussen -- 4/30/2008, 9:32 am
Re: Urethane Safety Issues
Ted Henry -- 4/29/2008, 9:11 pm
Re: Urethane Safety Issues
Steve Rasmussen -- 4/29/2008, 9:37 pm
Re: Urethane Safety Issues
Bill Hamm -- 4/30/2008, 1:14 am
Re: Urethane Safety Issues
Steve Rasmussen -- 4/29/2008, 7:50 pm
Re: Material: hBN Coating Abrasion Test
Bryan Hansel -- 4/29/2008, 9:44 am
Re: Material: hBN Coating Abrasion Test
Acors -- 5/9/2008, 6:01 pm
Re: Material: hBN Coating Abrasion Test
Dan Caouette (CSFW) -- 4/30/2008, 9:40 am
Re: Material: hBN Coating Abrasion Test
Bill Hamm -- 4/30/2008, 1:07 am
Re: Material: hBN Coating Abrasion Test
Bryan Hansel -- 4/30/2008, 8:58 am
Re: Material: hBN Coating Abrasion Test
Bill Hamm -- 5/1/2008, 1:21 am
Test Link *LINK*
Dan Caouette (CSFW) -- 4/29/2008, 8:27 am
question
LeeG -- 5/14/2008, 12:48 pm
Re: question------WebKitFormBoundaryaMY9uSPYUF94+D
Dan Caouette (CSFW)------WebKitFormBoundaryaMY9uSP -- 5/14/2008, 3:17 pm
Re: Test Link
Dave Reekie -- 4/29/2008, 1:14 pm