Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Urethane Safety Issues
By:Roy
Date: 5/7/2008, 11:05 am
In Response To: Urethane Safety Issues (Ted Henry)

SNIP

As far as I can tell there
: is only one cartridge (made by 3M) that is specifically approved for
: isocyanates. It's no wonder autobody shops require a license (Washington
: State) to use this type of product.

SNIP

Hi Ted

I was being lazy before asking about the canister filter for isocynates.

With no T1 and no DSL and only on a slow modem, I didn't want to satisfy my curosity as to the existance of any cartridge being exceptable for even a minimal amount of exposure to them.

I finally did however go looking and found the same unsubstantiated statment on a wood working page...no filter numbers to go look at the 3 M page and verify either

It would seem without a specific filter number the statement that there is only one that is recomended, is false...I could find none that is recomended by 3 M for use with Isocynates.....

Looks like if spraying....even with minimual exposure....airpump/seperate air system is the only sugested system.

Best wishes
Roy

Too bad...the hose is a pain

Messages In This Thread

Material: hBN Coating Abrasion Test *LINK*
Dan Caouette (CSFW) -- 4/29/2008, 8:25 am
Re: Material: hBN Coating Abrasion Test
Acors -- 5/9/2008, 5:11 pm
Re: Material: hBN Coating Abrasion Test------WebKi
Dan Caouette (CSFW------WebKitFormBoundaryHAvdf7mj -- 5/12/2008, 8:21 am
Re: Material: hBN Coating Abrasion Test
Bill Hamm -- 4/30/2008, 1:05 am
Re: Material: hBN Coating Abrasion Test
Robert N Pruden -- 5/2/2008, 1:50 pm
Re: Material: hBN Coating Abrasion Test
Dan Caouette (CSFW) -- 4/30/2008, 10:17 am
Urethane Safety Issues
Ted Henry -- 4/29/2008, 4:57 pm
Re: Urethane Safety Issues
Roy -- 5/7/2008, 11:05 am
Re: Urethane Safety Issues
Roy -- 5/4/2008, 11:06 am
Re: Urethane Safety Issues
Bill Hamm -- 5/5/2008, 2:10 am
Ditto to what Bill said...------WebKitFormBoundary
Dan Caouette (CSFW)------WebKitFormBoundarydta+Yzz -- 5/5/2008, 9:00 am
Re: Urethane Safety Issues
Roy -- 5/5/2008, 5:58 am
Re: Urethane Safety Issues
Dan Caouette (CSFW) -- 4/30/2008, 10:02 am
Re: Urethane Safety Issues
Dan Caouette (CSFW) -- 4/30/2008, 10:06 am
Part III
Dan Caouette (CSFW) -- 4/30/2008, 10:06 am
Part II
Dan Caouette (CSFW) -- 4/30/2008, 10:04 am
Re: Urethane Safety Issues Part 1
Dan Caouette (CSFW) -- 4/30/2008, 10:03 am
Re: Urethane Safety Issues
Steve Rasmussen -- 4/29/2008, 5:21 pm
Re: Urethane Safety Issues
Bill Hamm -- 4/30/2008, 1:11 am
Re: Urethane Safety Issues
Steve Rasmussen -- 4/30/2008, 9:32 am
Re: Urethane Safety Issues
Ted Henry -- 4/29/2008, 9:11 pm
Re: Urethane Safety Issues
Steve Rasmussen -- 4/29/2008, 9:37 pm
Re: Urethane Safety Issues
Bill Hamm -- 4/30/2008, 1:14 am
Re: Urethane Safety Issues
Steve Rasmussen -- 4/29/2008, 7:50 pm
Re: Material: hBN Coating Abrasion Test
Bryan Hansel -- 4/29/2008, 9:44 am
Re: Material: hBN Coating Abrasion Test
Acors -- 5/9/2008, 6:01 pm
Re: Material: hBN Coating Abrasion Test
Dan Caouette (CSFW) -- 4/30/2008, 9:40 am
Re: Material: hBN Coating Abrasion Test
Bill Hamm -- 4/30/2008, 1:07 am
Re: Material: hBN Coating Abrasion Test
Bryan Hansel -- 4/30/2008, 8:58 am
Re: Material: hBN Coating Abrasion Test
Bill Hamm -- 5/1/2008, 1:21 am
Test Link *LINK*
Dan Caouette (CSFW) -- 4/29/2008, 8:27 am
question
LeeG -- 5/14/2008, 12:48 pm
Re: question------WebKitFormBoundaryaMY9uSPYUF94+D
Dan Caouette (CSFW)------WebKitFormBoundaryaMY9uSP -- 5/14/2008, 3:17 pm
Re: Test Link
Dave Reekie -- 4/29/2008, 1:14 pm