Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Material: Using tung oil
By:Bill Hamm
Date: 3/7/2010, 12:43 am
In Response To: Re: Material: Using tung oil (Mike Bielski)

: The tip from Le Tonkinois is a good one, as long as your plastic
: bottle is air tight. When you open the tin oxygen gets in, so
: you either have to transfer the contents as was suggested, or
: use a product like Bloxygen, which is a spray of inert gas. If
: you don't, there is all of that oxygen in the top of your tin
: reacting with the oil.

: I started mixing shellac a while ago too, because sometimes even
: the new cans I bought wouldn't pass the drying on glass
: overnight test. I think it's a much higher quality product when
: you mix it yourself too. Anyway- I think there's a similar test
: for oils on glass.

: m

Cheaper to use propane from an unlit torch bled into the opened can, it's heavier than air and will displace the oxygen.

Bill H.

Messages In This Thread

Material: Using tung oil
George -- 3/2/2010, 9:23 am
Re: Material: Using tung oil
Mike Bielski -- 3/5/2010, 8:23 am
Re: Material: Using tung oil
George -- 3/5/2010, 1:15 pm
Re: Material: Using tung oil
Mike Savage -- 3/6/2010, 5:49 am
Re: Material: Using tung oil
Bill Hamm -- 3/7/2010, 12:45 am
Re: Material: Using tung oil
Mike Savage -- 3/7/2010, 5:38 am
Re: Material: Using tung oil
Bill Hamm -- 3/8/2010, 12:27 am
Re: Material: Using tung oil
Mike Savage -- 3/8/2010, 6:10 am
Re: Material: Using tung oil
Bill Hamm -- 3/9/2010, 12:47 am
Re: Material: Using tung oil
george -- 3/8/2010, 5:24 am
Re: Material: Using tung oil
Mike Bielski -- 3/5/2010, 6:58 pm
Re: Material: Using tung oil
Bill Hamm -- 3/7/2010, 12:43 am
Re: Material: Using tung oil
Brian Nystrom -- 3/6/2010, 9:40 am
Re: Material: Using tung oil
Brian Nystrom -- 3/3/2010, 8:36 am
Re: Material: Using tung oil
George -- 3/4/2010, 4:19 am
Re: Material: Using tung oil
Bill Hamm -- 3/7/2010, 12:31 am
Re: Material: Using tung oil
Brian Nystrom -- 3/4/2010, 7:44 am
Re: Material: Using tung oil
George -- 3/5/2010, 4:36 am
Re: Material: Using tung oil
Brian Nystrom -- 3/5/2010, 7:10 am
Re: Material: Using tung oil
George -- 3/5/2010, 1:06 pm
Re: Material: Using tung oil
George -- 3/8/2010, 12:49 pm
Re: Material: Using tung oil
Mike Savage -- 3/5/2010, 6:29 am
Re: Material: Using tung oil
Brian Nystrom -- 3/5/2010, 7:01 am
Re: Material: Using tung oil
Mike Savage -- 3/5/2010, 2:41 pm
Re: Material: Using tung oil
Mike Bielski -- 3/5/2010, 8:14 am
Re: Material: Using tung oil
Bill Hamm -- 3/7/2010, 12:36 am
Re: Material: Using tung oil
Ben Blackburn -- 3/5/2010, 4:50 am
Re: Material: Using tung oil *PIC*
Ben Blackburn -- 3/4/2010, 11:03 am
Re: Material: Using tung oil
Brian Nystrom -- 3/4/2010, 7:52 pm