Re: Laminated Frame**s?
In Response To: Re: Laminated Frame**s? (Bill Hamm)
I have 3 or 4 sheets of 3mm ply in the shop. Very bendy stuff and I looked at something similar. The problem I saw was the bends were really tight with hard chines. The ply would want to break before it bent. I could make the bends but I figured that was a weak point too. So I thought about thin strips and glueing them up but it seemed like a lot of work for minimal gain so I never pursued it. There are some cool bragging rights there if you like the work, but it just didn't appeal to me.
Plus I did some calculating and you only saw about an 1/8 mph increase for loosing 25 lbs.
Messages In This Thread
- Other: Kudzu + Bill - can't open messages
Doug S -- 7/16/2010, 7:36 pm- *** AVOID THE WORD ... ***
Doug S -- 7/17/2010, 9:38 am- Re: *** AVOID THE WORD ... ***
Bill Hamm -- 7/18/2010, 12:18 am
- Me either!
Kudzu -- 7/17/2010, 8:43 am- Re: Me either!
Bill Hamm -- 7/18/2010, 12:16 am
- Re: Other: Kudzu + Bill - can't open messages
Bill Hamm -- 7/17/2010, 12:13 am- Re: Laminated Frames?
brian scarborough -- 7/17/2010, 7:56 am- Re: Laminated Frame**s?
Kudzu -- 7/17/2010, 11:55 am- Re: Laminated Frame**s?
Bill Hamm -- 7/18/2010, 12:08 am- Re: Laminated Frame**s?
Bill Hamm -- 7/17/2010, 1:39 pm- Re: Laminated Frame**s?
Kudzu -- 7/17/2010, 1:50 pm- Re: Laminated Frame**s?
Bill Hamm -- 7/18/2010, 1:45 am- Re: Laminated Frame**s?
Bill Hamm -- 7/17/2010, 1:54 pm- Re: Laminated Frame**s?
Kudzu -- 7/17/2010, 4:23 pm- Re: Laminated Frame**s?
Bill Hamm -- 7/18/2010, 12:10 am- Re: Laminated Frame**s?
Dan Caouette (CSFW) -- 7/17/2010, 5:31 pm- Re: Laminated Frame**s?
Bill Hamm -- 7/18/2010, 12:12 am- plans
Dan Caouette (CSFW) -- 7/19/2010, 8:31 am
- plans
- Re: Laminated Frame**s?
- Re: Laminated Frame**s?
- Re: Laminated Frame**s?
- Re: Laminated Frame**s?
- Re: Laminated Frame**s?
- Link for Bryan's message
Doug S -- 7/17/2010, 9:39 am - Re: Laminated Frame**s?
- Re: Other: Kudzu + Bill - can't open messages
Bill Hamm -- 7/17/2010, 5:05 am- Lightweight SOFs...
Dan Caouette (CSFW) -- 7/17/2010, 10:59 am- Re: Lightweight SOFs...
Bill Hamm -- 7/17/2010, 1:30 pm- Re: Lightweight SOFs...
Dan Caouette (CSFW) -- 7/19/2010, 8:27 am- Re: Lightweight SOFs...
Bill Hamm -- 7/19/2010, 8:46 am
- Re: Lightweight SOFs...
Dan Caouette (CSFW) -- 7/17/2010, 5:32 pm - Re: Lightweight SOFs...
- Re: Lightweight SOFs...
- Re: Lightweight SOFs...
- Re: Laminated Frame**s?
- Re: Other: Kudzu + Bill - can't open messages
Peter B -- 7/16/2010, 8:53 pm- Re: Other: Kudzu + Bill - can't open messages
wwfloyd -- 7/16/2010, 8:35 pm - Re: *** AVOID THE WORD ... ***
- *** AVOID THE WORD ... ***