Date: 1/3/2011, 2:39 pm
: Now how did I know that there must be an electrician or two on this
: forum. :)
: Yes, the setup that I use could shock you. The simplest fix is to
: leave the iron handle on, which, if you are more skilled than I
: was at figuring out how to get it off in one piece, will work
: fine. It will make clamping the thing down a bit more of a
: challenge, but that problem should be solvable. In any case, if
: the handle is left on, the unit could be used in hand held mode,
: which may prove advantageous.
: Although the shock hazard looks high, I find that I am working on
: the opposite side of the iron from the wiring, and the support
: frames protect the innards to some degree. I will continue to
: use the thing as it is, but I don't recommend the open wiring to
: others, particularly not others with kids around. As mentioned
: elsewhere a gfci outlet would be a great idea, and they are
: reasonably cheap even if purchased just for the project. If
: using a rig like this outdoors or in a damp environment, a gfci
: outlet would be absolutely necessary.
: Thanks everyone for bringing this issue up,
: Best regards,
: Allan Edie
Allan
I hope you didn't take my comments as criticism. I'm sure you know what you're doing. I go to great lengths to 'grandson' proof my shop, and something like that 'tingles the spider sense'. I does look like a great rig for bending strips.
Kirk
Messages In This Thread
- Strip: heat guns
george jung -- 12/30/2010, 6:36 pm- Re: Strip: heat guns
Allan -- 12/30/2010, 11:46 pm- Re: Strip: heat guns
Simeon -- 12/30/2010, 7:24 pm- Re: Strip: heat guns *PIC*
Al Edie -- 12/30/2010, 9:01 pm- Re: Strip: heat guns
Bill Hamm -- 12/30/2010, 11:37 pm- Re: Strip: heat guns
Simeon -- 12/31/2010, 3:17 am- Re: Strip: heat guns
Bill Hamm -- 12/31/2010, 8:41 am- Re: Strip: heat guns
george jung -- 12/31/2010, 10:35 am- Re: Strip: heat guns
Al Edie -- 12/31/2010, 11:04 am- Shock protection?
Paul G. Jacobson -- 12/31/2010, 9:21 pm- Re: Shock protection?
Kirk Fredericks -- 12/31/2010, 10:17 pm- Re: Shock protection?
george jung -- 1/1/2011, 12:49 pm- Re: Shock protection?
Kirk Fredericks -- 1/1/2011, 1:25 pm- Re: Shock protection?
Bill Hamm -- 1/1/2011, 10:54 pm- Re: Shock protection?
Kirk Fredericks -- 1/2/2011, 12:36 am- Re: Shock protection?
Al Edie -- 1/3/2011, 1:47 pm- Re: Shock protection?
Kirk Fredericks -- 1/3/2011, 2:39 pm- Re: Shock protection?
Al Edie -- 1/3/2011, 4:21 pm- Re: Shock protection?
george jung -- 1/4/2011, 7:25 pm
- Re: Shock protection?
- Re: Shock protection?
- Re: Shock protection?
- Re: Shock protection?
- Re: Shock protection?
- Re: Shock protection?
- Re: Shock protection?
- Re: Shock protection?
- Re: Strip: heat guns
george jung -- 12/31/2010, 2:00 pm- Re: Strip: heat guns
Al Edie -- 12/31/2010, 9:21 pm- Re: Strip: heat guns
Bill Hamm -- 12/31/2010, 5:37 pm - Re: Strip: heat guns
- Re: Shock protection?
- Shock protection?
- Re: Strip: heat guns
- Re: Strip: heat guns
- Re: Strip: heat guns
- Re: Strip: heat guns
- Re: Strip: heat guns *PIC*
Al Edie -- 12/30/2010, 8:56 pm - Re: Strip: heat guns
- Re: Strip: heat guns
Bill Hamm -- 12/30/2010, 7:11 pm- Re: Strip: heat guns
David Bynoe -- 12/30/2010, 7:00 pm - Re: Strip: heat guns
- Re: Strip: heat guns