Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Thanks all
By:Bill Hamm
Date: 1/17/2011, 6:43 am
In Response To: Thanks all (Stephen Troy)

: Wow! Busy thread, thanks.

: So here's the setup I have.

: The table saw is a Delta Unisaw with a 4' plywood section attached
: to the (4') Unifence. Featherboard attached to that. I set up a
: long outfeed table with a length of stiff clear plastic for the
: slipperiness. Sawhorse behind me to help support the long board.

: I ripped the 2x12 in half, and about every six passes I'd run a
: combination square down the edge to see how it was going. Once I
: got 1/8" out of line, I'd flip the board, and adjust the
: saw to rip 1/4" from the narrowest part of the board. The
: thicker parts would end up thicker but no big deal, that's what
: the planer's for.

: Slow work, but two big boards are now a lot of skinny strips. I
: still need to rip each of them in half (they're 1.5" wide
: right now), but that was enough for this weekend.

: Do you still use a featherboard when ripping strips in half? Seems
: like that would be tricky.

I'd want a featherboard behind the blade to hold the strip down, the blade behind the cut is going upwards and will want to lift the light strips, can be dangerous letting that happen, doesn't need much force on it, just keep the strip on the table.

Bill H.

Messages In This Thread

Strip: Ripping better strips
Stephen Troy -- 1/15/2011, 11:29 pm
Re: Strip: Ripping better strips
Bill Hamm -- 1/16/2011, 12:53 am
Re: Strip: Ripping better strips
Al Edie -- 1/16/2011, 3:19 am
Re: Strip: Ripping better strips
Bill Hamm -- 1/16/2011, 3:27 am
Re: Strip: Ripping better strips
Al Edie -- 1/16/2011, 3:38 am
Re: Strip: Ripping better strips
Bill Hamm -- 1/16/2011, 7:04 am
Re: Strip: Ripping better strips
Tony Olsen -- 1/16/2011, 9:02 am
Re: Strip: Ripping better strips
Mike Savage -- 1/16/2011, 12:42 pm
Re: Strip: Ripping better strips
Paul G. Jacobson -- 1/16/2011, 1:37 pm
Re: Strip: Ripping better strips
Ken Blanton -- 1/16/2011, 5:55 am
Re: Strip: Ripping better strips
Jay Babina -- 1/16/2011, 9:01 am
Re: Strip: Ripping better strips
Ian Cummins -- 1/16/2011, 5:08 pm
Re: Strip: Ripping better strips
Kurt Maurer -- 1/16/2011, 7:23 pm
Re: Strip: Zen
Ian Johnson -- 1/16/2011, 8:08 pm
Re: Strip: Ripping better strips
Kirk Fredericks -- 1/16/2011, 10:49 pm
Re: Strip: Ripping better strips
Tony Olsen -- 1/16/2011, 10:58 pm
Re: Strip: Ripping better strips
Kirk Fredericks -- 1/16/2011, 11:04 pm
Re: Strip: Ripping better strips
Paul G. Jacobson -- 1/16/2011, 9:10 pm
Re: Strip: Ripping better strips
Phil Nelson -- 1/16/2011, 10:03 pm
Re: Strip: Ripping better strips
ancient kayaker -- 1/18/2011, 10:39 am
Re: Strip: Ripping better strips
Phil Nelson -- 1/18/2011, 4:17 pm
Thanks all
Stephen Troy -- 1/17/2011, 12:31 am
Re: Thanks all
Paul G. Jacobson -- 1/17/2011, 4:02 am
Re: Thanks all
Bill Hamm -- 1/17/2011, 6:43 am
Featherboard use *PIC*
Paul G. Jacobson -- 1/17/2011, 6:50 pm
Re: Featherboard use
Les Cheeseman -- 1/20/2011, 9:54 am
Re: Featherboard use
Bill Hamm -- 1/20/2011, 10:08 am
Re: Featherboard use
Les Cheeseman -- 1/20/2011, 11:28 am
Re: Featherboard use
Bill Hamm -- 1/20/2011, 10:13 am
Re: Featherboard use
Bill Hamm -- 1/20/2011, 10:32 am
Re: Thanks all
Les Cheeseman -- 1/19/2011, 9:18 am
Re: Thanks all
Bill Hamm -- 1/19/2011, 9:28 am
infeeed.outfeed table extensions.
Paul G. Jacobson -- 1/19/2011, 8:00 pm
And the picture for that is--- *PIC*
Paul G. Jacobson -- 1/19/2011, 8:06 pm
Re: And the picture for that is---
Bill Hamm -- 1/19/2011, 8:52 pm
Re: And the picture for that is---
Bill Hamm -- 1/19/2011, 8:58 pm
Re: And the picture for that is---
Les Cheeseman -- 1/20/2011, 9:47 am
Re: And the picture for that is--- *PIC*
Etienne Muller - ireland -- 1/20/2011, 4:39 pm
Re: And the picture for that is---
Les Cheeseman -- 1/21/2011, 3:54 am
Re: Strip: Ripping better strips
Etienne Muller - ireland -- 1/17/2011, 5:07 am