: Thanks all for the input.
: I don't think getting the right temperature will be much of an
: issue. Here in Ohio is in the 90's during the day and 70's, at
: night at least for next few days.
: @Rob : not a manual for say. I have been going off of "The
: Strip-Built Sea Kayak", "Kayakcraft: fine woodstrip
: kayak construction" and your web site along with others...
: Also I have some cross grain sanding scratches (yes I know allays
: sand with the grain ... ) which your state will show up like a
: sore thumb in a clear layup. I was wandering just how much
: scratches and minor imperfections (gaps about 1/32 or less ) are
: magnified after finishing? I am hesitant to do any more sanding
: because even with a long fairing board and fresh sand paper
: (changing every 5 min or less) the softer wood is starting to
: cup out. It is not extream but it is noticeable when you run
: your hand over it. I would say 5 to 15 mills max.
Gaps need to be filled regardless, can't sand out gaps.
Bill H.
Messages In This Thread
- Epoxy: Fill Coat and glassing time line and other questio *PIC*
Jmoore -- 9/1/2011, 7:31 pm- Re: Epoxy: Fill Coat and glassing time line and ot
Etiennemuller Muller Ireland -- 9/1/2011, 8:05 pm- Re: Epoxy: Fill Coat and glassing time line and ot
Rob Macks / Laughing Loon CC&K -- 9/1/2011, 8:20 pm- Re: Epoxy: Fill Coat and glassing time line and ot
Eric M. -- 9/2/2011, 11:37 am- Re: Epoxy: Fill Coat and glassing time line and ot
Jmoore -- 9/2/2011, 12:49 pm- Re: Epoxy: Fill Coat and glassing time line and ot
Rob Macks / Laughing Loon CC&K -- 9/2/2011, 1:42 pm- Re: Epoxy: Fill Coat and glassing time line and ot
Jmoore -- 9/2/2011, 1:58 pm
- Re: Epoxy: Fill Coat and glassing time line and ot
Bill Hamm -- 9/3/2011, 1:19 am - Re: Epoxy: Fill Coat and glassing time line and ot
- Re: Epoxy: Fill Coat and glassing time line and ot
Greg New -- 9/2/2011, 7:07 pm- Bit the bulit and just did it *PIC*
Jmoore -- 9/5/2011, 2:45 pm- Should not have lissend to dad! *PIC*
Jmoore -- 9/5/2011, 3:54 pm- Re: Should not have lissend to dad!
Rick Jensen -- 9/5/2011, 4:38 pm- Re: Should not have lissend to dad!
dave g -- 9/5/2011, 8:56 pm- Re: Should not have lissend to dad!
Etiennemuller Muller Ireland -- 9/6/2011, 5:08 am
- Re: Should not have lissend to dad!
- Re: Should not have lissend to dad!
Mike Savage -- 9/6/2011, 1:43 pm - Re: Should not have lissend to dad!
- Re: Bit the bulit and just did it
Bill Hamm -- 9/6/2011, 2:00 am- Re: Bit the bulit and just did it
Sean D -- 9/6/2011, 10:32 am- Re: Bit the bulit and just did it
Jmoore -- 9/6/2011, 12:03 pm
- Re: Bit the bulit and just did it
- Re: Should not have lissend to dad!
- Re: Epoxy: Fill Coat and glassing time line and ot
- Re: Epoxy: Fill Coat and glassing time line and ot