Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: few questions about milling the strips
By:skrap1r0n
Date: 11/18/2011, 9:02 pm
In Response To: Re: Strip: few questions about milling the strips (Allan)

: If you do that, you have to handle 18' long pieces of timber on the
: saw bench, on the router table and when you are attaching the
: strips.

: Like a lot of other people, I find 9' strips easier to handle. In
: fact I often use shorter lengths.

: Just joint them as you fit them on the forms.

Oh no, I'm milling 9' lengths, I meant that I am going to scarf each strip prior to attaching it. No way am I going to manhandle an 18' board over the saw or through the router

Messages In This Thread

Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 3:51 pm
Re: Strip: few questions about milling the strips
Donovan -- 11/18/2011, 4:07 pm
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 4:26 pm
Re: Strip: few questions about milling the strips
StephenHJ -- 11/22/2011, 12:54 pm
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/23/2011, 2:36 am
Re: Strip: few questions about milling the strips
Mike Savage -- 11/23/2011, 11:28 am
Re: Strip: few questions about milling the strips
Kevin McAtee -- 11/23/2011, 6:22 pm
Re: Strip: few questions about milling the strips *PIC*
Rick -- 11/24/2011, 2:18 pm
Re: Strip: few questions about milling the strips *PIC*
Dwight Lynn -- 11/18/2011, 6:03 pm
Re: Strip: few questions about milling the strips
Etienne Muller -- 11/18/2011, 6:15 pm
Re: Strip: few questions about milling the strips
Dwight Lynn -- 11/18/2011, 6:22 pm
Re: Strip: few questions about milling the strips
Etienne Muller -- 11/18/2011, 6:36 pm
Re: Strip: few questions about milling the strips *PIC*
Dan Caouette (CSFW) -- 11/18/2011, 6:44 pm
Re: Strip: few questions about milling the strips
Mike Bielski -- 11/19/2011, 12:00 am
Re: Strip: few questions about milling the strips
Etienne Muller -- 11/19/2011, 4:38 am
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/20/2011, 2:17 am
Re: Strip: few questions about milling the strips
Dan Caouette (CSFW) -- 11/19/2011, 5:52 am
Re: Strip: few questions about milling the strips
Mike Bielski -- 11/19/2011, 12:37 pm
Re: Strip: few questions about milling the strips
ancient kayaker -- 11/20/2011, 9:43 am
Re: Strip: few questions about milling the strips
ancient kayaker -- 11/20/2011, 9:44 am
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/21/2011, 1:27 am
Re: Strip: few questions about milling the strips
Kevin McAtee -- 11/25/2011, 8:02 pm
Re: Strip: few questions about milling the strips
ancient kayaker -- 11/25/2011, 9:01 pm
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 8:08 pm
Re: Strip: few questions about milling the strips
Clayton Plunkett -- 11/21/2011, 10:57 am
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/22/2011, 12:28 am
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/22/2011, 12:46 am
Re: Strip: few questions about milling the strips
Kevin Greer -- 11/18/2011, 7:02 pm
Re: Strip: few questions about milling the strips
Allan -- 11/18/2011, 8:46 pm
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 9:02 pm
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/19/2011, 2:55 am
1/4 in strips
Jay Babina -- 11/22/2011, 2:43 pm
Re: 1/4 in strips *PIC*
John Caldeira -- 11/24/2011, 2:41 am
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/22/2011, 10:14 pm
Re: Strip: few questions about milling the strips
Paul G. Jacobson -- 11/22/2011, 10:50 pm
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/23/2011, 2:37 am
OT: I'm back
Paul G. Jacobson -- 11/23/2011, 8:36 pm
Re: OT: I'm back
Bill Hamm -- 11/24/2011, 2:59 am
Re: OT: I'm back
ancient kayaker -- 11/24/2011, 5:56 pm
Re: OT: I'm back
Bill Hamm -- 11/26/2011, 2:23 am