Boat Building Forum
Find advice on all aspects of building your own kayak, canoe or any lightweight boats
Re: Strip: few questions about milling the strips
In Response To: Re: Strip: few questions about milling the strips (Mike Bielski)
: I had a clean shop when the guy from Fine Woodworking came to
: photograph me in it for the article I wrote. Man that was a lot
: of work. When I worked in a professional shop we spend half of
: every friday cleaning. If I had half a day a week to clean my
: shop it would still look awesome, but right now most of the time
: I don't have that much time spread out over a single week,
: sometimes two.
: Of course, now everything takes twice as long because nothing is
: ever put away where it belongs...
: m
The upside is that one develops the talent for finding things.
Et
Messages In This Thread
- Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 3:51 pm- Re: Strip: few questions about milling the strips
Donovan -- 11/18/2011, 4:07 pm- Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 4:26 pm- Re: Strip: few questions about milling the strips
StephenHJ -- 11/22/2011, 12:54 pm- Re: Strip: few questions about milling the strips
Bill Hamm -- 11/23/2011, 2:36 am- Re: Strip: few questions about milling the strips
Mike Savage -- 11/23/2011, 11:28 am- Re: Strip: few questions about milling the strips
Kevin McAtee -- 11/23/2011, 6:22 pm- Re: Strip: few questions about milling the strips *PIC*
Rick -- 11/24/2011, 2:18 pm - Re: Strip: few questions about milling the strips *PIC*
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips *PIC*
Dwight Lynn -- 11/18/2011, 6:03 pm- Re: Strip: few questions about milling the strips
Etienne Muller -- 11/18/2011, 6:15 pm- Re: Strip: few questions about milling the strips
Dwight Lynn -- 11/18/2011, 6:22 pm- Re: Strip: few questions about milling the strips
Etienne Muller -- 11/18/2011, 6:36 pm
- Re: Strip: few questions about milling the strips *PIC*
Dan Caouette (CSFW) -- 11/18/2011, 6:44 pm- Re: Strip: few questions about milling the strips
Mike Bielski -- 11/19/2011, 12:00 am- Re: Strip: few questions about milling the strips
Etienne Muller -- 11/19/2011, 4:38 am- Re: Strip: few questions about milling the strips
Bill Hamm -- 11/20/2011, 2:17 am
- Re: Strip: few questions about milling the strips
Dan Caouette (CSFW) -- 11/19/2011, 5:52 am- Re: Strip: few questions about milling the strips
Mike Bielski -- 11/19/2011, 12:37 pm
- Re: Strip: few questions about milling the strips
ancient kayaker -- 11/20/2011, 9:43 am- Re: Strip: few questions about milling the strips
ancient kayaker -- 11/20/2011, 9:44 am- Re: Strip: few questions about milling the strips
Bill Hamm -- 11/21/2011, 1:27 am- Re: Strip: few questions about milling the strips
Kevin McAtee -- 11/25/2011, 8:02 pm- Re: Strip: few questions about milling the strips
ancient kayaker -- 11/25/2011, 9:01 pm
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 8:08 pm- Re: Strip: few questions about milling the strips
Clayton Plunkett -- 11/21/2011, 10:57 am- Re: Strip: few questions about milling the strips
skrap1r0n -- 11/22/2011, 12:28 am- Re: Strip: few questions about milling the strips
Bill Hamm -- 11/22/2011, 12:46 am - Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
Kevin Greer -- 11/18/2011, 7:02 pm- Re: Strip: few questions about milling the strips
Allan -- 11/18/2011, 8:46 pm- Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 9:02 pm- Re: Strip: few questions about milling the strips
Bill Hamm -- 11/19/2011, 2:55 am - Re: Strip: few questions about milling the strips
- 1/4 in strips
Jay Babina -- 11/22/2011, 2:43 pm- Re: 1/4 in strips *PIC*
John Caldeira -- 11/24/2011, 2:41 am
- Re: Strip: few questions about milling the strips
skrap1r0n -- 11/22/2011, 10:14 pm- Re: Strip: few questions about milling the strips
Paul G. Jacobson -- 11/22/2011, 10:50 pm- Re: Strip: few questions about milling the strips
Bill Hamm -- 11/23/2011, 2:37 am- OT: I'm back
Paul G. Jacobson -- 11/23/2011, 8:36 pm- Re: OT: I'm back
Bill Hamm -- 11/24/2011, 2:59 am- Re: OT: I'm back
ancient kayaker -- 11/24/2011, 5:56 pm- Re: OT: I'm back
Bill Hamm -- 11/26/2011, 2:23 am
- Re: OT: I'm back
- Re: OT: I'm back
- Re: OT: I'm back
- OT: I'm back
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
