Boat Building Forum
Find advice on all aspects of building your own kayak, canoe or any lightweight boats
: In reading others build logs, they have another method when trying
: to avoid staples. The hot glue the strip directly to the forms,
: and when it's time to remove the forms a quick blow with a
: hammer is enough to break the hot glue. I'd suggest doing a
: little more research on how others are doing it around here
: before trying to reinvent the processes that have been proven to
: work for others.
: Just my .02 cents. I'm going SOF rather than strip, so take my info
: for what it's worth.
: Stephen HJ
I've also seen an interesting method where the strips were tied onto the forms using monofiliment fishing line, after the hull is complete the line is just cut off from the inside and sands just like wood. If the right test line is used (no idea what strength line to use) would have a bit of stretch to hold the strips snug.
I think WoodenBoat magazine did an article about this method.
Bill H.
Messages In This Thread
- Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 3:51 pm- Re: Strip: few questions about milling the strips
Donovan -- 11/18/2011, 4:07 pm- Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 4:26 pm- Re: Strip: few questions about milling the strips
StephenHJ -- 11/22/2011, 12:54 pm- Re: Strip: few questions about milling the strips
Bill Hamm -- 11/23/2011, 2:36 am- Re: Strip: few questions about milling the strips
Mike Savage -- 11/23/2011, 11:28 am- Re: Strip: few questions about milling the strips
Kevin McAtee -- 11/23/2011, 6:22 pm- Re: Strip: few questions about milling the strips *PIC*
Rick -- 11/24/2011, 2:18 pm - Re: Strip: few questions about milling the strips *PIC*
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips *PIC*
Dwight Lynn -- 11/18/2011, 6:03 pm- Re: Strip: few questions about milling the strips
Etienne Muller -- 11/18/2011, 6:15 pm- Re: Strip: few questions about milling the strips
Dwight Lynn -- 11/18/2011, 6:22 pm- Re: Strip: few questions about milling the strips
Etienne Muller -- 11/18/2011, 6:36 pm
- Re: Strip: few questions about milling the strips *PIC*
Dan Caouette (CSFW) -- 11/18/2011, 6:44 pm- Re: Strip: few questions about milling the strips
Mike Bielski -- 11/19/2011, 12:00 am- Re: Strip: few questions about milling the strips
Etienne Muller -- 11/19/2011, 4:38 am- Re: Strip: few questions about milling the strips
Bill Hamm -- 11/20/2011, 2:17 am
- Re: Strip: few questions about milling the strips
Dan Caouette (CSFW) -- 11/19/2011, 5:52 am- Re: Strip: few questions about milling the strips
Mike Bielski -- 11/19/2011, 12:37 pm
- Re: Strip: few questions about milling the strips
ancient kayaker -- 11/20/2011, 9:43 am- Re: Strip: few questions about milling the strips
ancient kayaker -- 11/20/2011, 9:44 am- Re: Strip: few questions about milling the strips
Bill Hamm -- 11/21/2011, 1:27 am- Re: Strip: few questions about milling the strips
Kevin McAtee -- 11/25/2011, 8:02 pm- Re: Strip: few questions about milling the strips
ancient kayaker -- 11/25/2011, 9:01 pm
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 8:08 pm- Re: Strip: few questions about milling the strips
Clayton Plunkett -- 11/21/2011, 10:57 am- Re: Strip: few questions about milling the strips
skrap1r0n -- 11/22/2011, 12:28 am- Re: Strip: few questions about milling the strips
Bill Hamm -- 11/22/2011, 12:46 am - Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
Kevin Greer -- 11/18/2011, 7:02 pm- Re: Strip: few questions about milling the strips
Allan -- 11/18/2011, 8:46 pm- Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 9:02 pm- Re: Strip: few questions about milling the strips
Bill Hamm -- 11/19/2011, 2:55 am - Re: Strip: few questions about milling the strips
- 1/4 in strips
Jay Babina -- 11/22/2011, 2:43 pm- Re: 1/4 in strips *PIC*
John Caldeira -- 11/24/2011, 2:41 am
- Re: Strip: few questions about milling the strips
skrap1r0n -- 11/22/2011, 10:14 pm- Re: Strip: few questions about milling the strips
Paul G. Jacobson -- 11/22/2011, 10:50 pm- Re: Strip: few questions about milling the strips
Bill Hamm -- 11/23/2011, 2:37 am- OT: I'm back
Paul G. Jacobson -- 11/23/2011, 8:36 pm- Re: OT: I'm back
Bill Hamm -- 11/24/2011, 2:59 am- Re: OT: I'm back
ancient kayaker -- 11/24/2011, 5:56 pm- Re: OT: I'm back
Bill Hamm -- 11/26/2011, 2:23 am
- Re: OT: I'm back
- Re: OT: I'm back
- Re: OT: I'm back
- OT: I'm back
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
- Re: Strip: few questions about milling the strips
