Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: few questions about milling the strips *PIC*
By:Rick
Date: 11/24/2011, 2:18 pm
In Response To: Re: Strip: few questions about milling the strips (Mike Savage)

: That would work but is likely to leave pressure gouges where the
: line goes around the edge of the strips. Wetting down the
: finished stripping might raise out the marks, though.

: Mike Savage
: South West Cork
Use 25lb test monofilament, strip bead up, little groove is curved, does not pass light, disappears with sanding. I've built a dozen boats this way, have to make sure that strips don't buckle with the added pressure as you work your way up, best way is to take several days to do the stripping. The screws in the form are so the fishing line pulls both in and down. Unlike Woodenboat, I use one length of line for each strip, start at the bow, and wind your way down the length of the boat, wrapping at each form and once in between forms, clamp off at the other end. When the whole boat is stripped, cut the fishing line where it passes under the sheer strip, and yank out the pieces (pull down, wear gloves). More pics at http://www.flickr.com/photos/oysterbayboats/
Best rgds

Rick

Messages In This Thread

Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 3:51 pm
Re: Strip: few questions about milling the strips
Donovan -- 11/18/2011, 4:07 pm
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 4:26 pm
Re: Strip: few questions about milling the strips
StephenHJ -- 11/22/2011, 12:54 pm
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/23/2011, 2:36 am
Re: Strip: few questions about milling the strips
Mike Savage -- 11/23/2011, 11:28 am
Re: Strip: few questions about milling the strips
Kevin McAtee -- 11/23/2011, 6:22 pm
Re: Strip: few questions about milling the strips *PIC*
Rick -- 11/24/2011, 2:18 pm
Re: Strip: few questions about milling the strips *PIC*
Dwight Lynn -- 11/18/2011, 6:03 pm
Re: Strip: few questions about milling the strips
Etienne Muller -- 11/18/2011, 6:15 pm
Re: Strip: few questions about milling the strips
Dwight Lynn -- 11/18/2011, 6:22 pm
Re: Strip: few questions about milling the strips
Etienne Muller -- 11/18/2011, 6:36 pm
Re: Strip: few questions about milling the strips *PIC*
Dan Caouette (CSFW) -- 11/18/2011, 6:44 pm
Re: Strip: few questions about milling the strips
Mike Bielski -- 11/19/2011, 12:00 am
Re: Strip: few questions about milling the strips
Etienne Muller -- 11/19/2011, 4:38 am
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/20/2011, 2:17 am
Re: Strip: few questions about milling the strips
Dan Caouette (CSFW) -- 11/19/2011, 5:52 am
Re: Strip: few questions about milling the strips
Mike Bielski -- 11/19/2011, 12:37 pm
Re: Strip: few questions about milling the strips
ancient kayaker -- 11/20/2011, 9:43 am
Re: Strip: few questions about milling the strips
ancient kayaker -- 11/20/2011, 9:44 am
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/21/2011, 1:27 am
Re: Strip: few questions about milling the strips
Kevin McAtee -- 11/25/2011, 8:02 pm
Re: Strip: few questions about milling the strips
ancient kayaker -- 11/25/2011, 9:01 pm
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 8:08 pm
Re: Strip: few questions about milling the strips
Clayton Plunkett -- 11/21/2011, 10:57 am
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/22/2011, 12:28 am
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/22/2011, 12:46 am
Re: Strip: few questions about milling the strips
Kevin Greer -- 11/18/2011, 7:02 pm
Re: Strip: few questions about milling the strips
Allan -- 11/18/2011, 8:46 pm
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 9:02 pm
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/19/2011, 2:55 am
1/4 in strips
Jay Babina -- 11/22/2011, 2:43 pm
Re: 1/4 in strips *PIC*
John Caldeira -- 11/24/2011, 2:41 am
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/22/2011, 10:14 pm
Re: Strip: few questions about milling the strips
Paul G. Jacobson -- 11/22/2011, 10:50 pm
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/23/2011, 2:37 am
OT: I'm back
Paul G. Jacobson -- 11/23/2011, 8:36 pm
Re: OT: I'm back
Bill Hamm -- 11/24/2011, 2:59 am
Re: OT: I'm back
ancient kayaker -- 11/24/2011, 5:56 pm
Re: OT: I'm back
Bill Hamm -- 11/26/2011, 2:23 am