Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: Best sanding practices
By:Etienne Muller
Date: 2/26/2012, 6:05 am
In Response To: Re: Strip: Best sanding practices (Bill Hamm)

: Yep, long board makes a world of a difference on a boat, ROS is a
: great tool, but it's contact surface is too small to even out
: the surface. I'm sure Rob's stripping results in a very fair
: surface that then allows him to only use the ROS, but not all
: have the same stripping skills as Rob so the long board is more
: important for them to get the surface truely fair.

: Bill H.

With three sixteenths strip thickness there is not much leeway for error. Real fairing, in the traditional sense, could leave one with very little wood in places, unless the accuracy is there to start with.

Anyone who is new enough to make an unfair strip boat is, I think, unlikely to be able to do a proper fairing job anyway.

I never felt the need to fair a strip boat. Sure there may be areas that are not 100%, but I have never been able to find them they are so minute.

I think the biggest cause of small dips is probably overworking small areas in an effort to eradicate perceived blemishes. If one keeps the ROS moving over a large enough area without defining boundaries in the process and just continues until it is all uniform it should be enough.

Getting rid of big dips or lumps is going to necessitate thinning the hull radically in places. Sounds more like a filling job to me.

Hand sanding! Yetch. Life is too short

Messages In This Thread

Strip: Best sanding practices
Robert l -- 2/24/2012, 12:03 am
Re: Strip: Best sanding practices
Jon Mortimer -- 2/24/2012, 6:39 am
Re: Strip: Best sanding practices
Rob Macks/Laughing Loon CC&K -- 2/24/2012, 9:13 am
Re: Strip: Best sanding practices
Etienne Muller -- 2/24/2012, 7:07 am
Re: Strip: Best sanding practices
Eric Mattison -- 2/24/2012, 7:26 pm
Re: Strip: Best sanding practices
Mike Bielski -- 2/25/2012, 2:20 am
Re: Strip: Best sanding practices
Rob Macks/Laughing Loon CC&K -- 2/25/2012, 9:21 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/25/2012, 12:54 pm
Re: Strip: Best sanding practices
Bill Hamm -- 2/26/2012, 1:10 am
Re: Strip: Best sanding practices
Etienne Muller -- 2/26/2012, 6:05 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/26/2012, 8:58 am
Re: Strip: Best sanding practices
ancient kayaker -- 2/26/2012, 12:46 pm
Re: Strip: Best sanding practices
Etienne Muller -- 2/26/2012, 1:10 pm
Re: Strip: Best sanding practices
Bill Hamm -- 2/27/2012, 2:05 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/27/2012, 10:49 am
Re: Strip: Best sanding practices
Bill Hamm -- 2/28/2012, 1:37 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/28/2012, 1:47 pm
Re: Strip: Best sanding practices
Etienne Muller -- 2/28/2012, 1:51 pm
Re: Strip: Best sanding practices
Justin -- 2/29/2012, 5:29 am
Re: Strip: Best sanding practices
Kirk Fredericks -- 2/29/2012, 5:22 pm
Re: Strip: Best sanding practices
ancient kayaker -- 2/27/2012, 11:16 pm
Re: Strip: Best sanding practices
dave g -- 2/28/2012, 12:42 am
Re: Strip: Best sanding practices
ancient kayaker -- 2/28/2012, 10:37 am
Re: Strip: Best sanding practices
Bill Hamm -- 2/28/2012, 1:40 am
Re: Strip: Best sanding practices
george jung -- 2/28/2012, 12:01 pm
Re: Strip: Best sanding practices
Bill Hamm -- 2/29/2012, 1:48 am
Re: Strip: Best sanding practices
John Abercrombie -- 2/28/2012, 3:48 am
Re: Strip: Best sanding practices
Rob Macks/Laughing Loon CC&K -- 2/27/2012, 11:08 am
Re: Strip: Best sanding practices
John Abercrombie -- 2/27/2012, 1:03 pm
Re: Strip: Best sanding practices
Rob Macks/Laughing Loon CC&K -- 2/28/2012, 4:15 pm
Re: Strip: Best sanding practices
dave g -- 2/27/2012, 10:41 pm
Re: Strip: Best sanding practices
Dan Caouette (CSFW) -- 2/27/2012, 11:55 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/27/2012, 7:56 pm
Re: Strip: Best sanding practices
dave g -- 2/27/2012, 10:09 pm
Re: Strip: Best sanding practices
Bill Hamm -- 2/27/2012, 2:02 am
Re: Strip: Best sanding practices
Scott Fitzgerrell -- 2/27/2012, 11:56 am
Re: Strip: Best sanding practices
Ian Johnson -- 2/26/2012, 6:37 pm