Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: Best sanding practices
By:Bill Hamm
Date: 2/27/2012, 2:02 am
In Response To: Re: Strip: Best sanding practices (Etienne Muller)

: With three sixteenths strip thickness there is not much leeway for
: error. Real fairing, in the traditional sense, could leave one
: with very little wood in places, unless the accuracy is there to
: start with.

: Anyone who is new enough to make an unfair strip boat is, I think,
: unlikely to be able to do a proper fairing job anyway.

: I never felt the need to fair a strip boat. Sure there may be areas
: that are not 100%, but I have never been able to find them they
: are so minute.

: I think the biggest cause of small dips is probably overworking
: small areas in an effort to eradicate perceived blemishes. If
: one keeps the ROS moving over a large enough area without
: defining boundaries in the process and just continues until it
: is all uniform it should be enough.

: Getting rid of big dips or lumps is going to necessitate thinning
: the hull radically in places. Sounds more like a filling job to
: me.

: Hand sanding! Yetch. Life is too short

Kayak is a tiny surface, no biggy to long board. Shouldn't take more than a couple hours max.

Good to build up those muscles so you're ready to paddle :)

Bill H.

Messages In This Thread

Strip: Best sanding practices
Robert l -- 2/24/2012, 12:03 am
Re: Strip: Best sanding practices
Jon Mortimer -- 2/24/2012, 6:39 am
Re: Strip: Best sanding practices
Rob Macks/Laughing Loon CC&K -- 2/24/2012, 9:13 am
Re: Strip: Best sanding practices
Etienne Muller -- 2/24/2012, 7:07 am
Re: Strip: Best sanding practices
Eric Mattison -- 2/24/2012, 7:26 pm
Re: Strip: Best sanding practices
Mike Bielski -- 2/25/2012, 2:20 am
Re: Strip: Best sanding practices
Rob Macks/Laughing Loon CC&K -- 2/25/2012, 9:21 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/25/2012, 12:54 pm
Re: Strip: Best sanding practices
Bill Hamm -- 2/26/2012, 1:10 am
Re: Strip: Best sanding practices
Etienne Muller -- 2/26/2012, 6:05 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/26/2012, 8:58 am
Re: Strip: Best sanding practices
ancient kayaker -- 2/26/2012, 12:46 pm
Re: Strip: Best sanding practices
Etienne Muller -- 2/26/2012, 1:10 pm
Re: Strip: Best sanding practices
Bill Hamm -- 2/27/2012, 2:05 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/27/2012, 10:49 am
Re: Strip: Best sanding practices
Bill Hamm -- 2/28/2012, 1:37 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/28/2012, 1:47 pm
Re: Strip: Best sanding practices
Etienne Muller -- 2/28/2012, 1:51 pm
Re: Strip: Best sanding practices
Justin -- 2/29/2012, 5:29 am
Re: Strip: Best sanding practices
Kirk Fredericks -- 2/29/2012, 5:22 pm
Re: Strip: Best sanding practices
ancient kayaker -- 2/27/2012, 11:16 pm
Re: Strip: Best sanding practices
dave g -- 2/28/2012, 12:42 am
Re: Strip: Best sanding practices
ancient kayaker -- 2/28/2012, 10:37 am
Re: Strip: Best sanding practices
Bill Hamm -- 2/28/2012, 1:40 am
Re: Strip: Best sanding practices
george jung -- 2/28/2012, 12:01 pm
Re: Strip: Best sanding practices
Bill Hamm -- 2/29/2012, 1:48 am
Re: Strip: Best sanding practices
John Abercrombie -- 2/28/2012, 3:48 am
Re: Strip: Best sanding practices
Rob Macks/Laughing Loon CC&K -- 2/27/2012, 11:08 am
Re: Strip: Best sanding practices
John Abercrombie -- 2/27/2012, 1:03 pm
Re: Strip: Best sanding practices
Rob Macks/Laughing Loon CC&K -- 2/28/2012, 4:15 pm
Re: Strip: Best sanding practices
dave g -- 2/27/2012, 10:41 pm
Re: Strip: Best sanding practices
Dan Caouette (CSFW) -- 2/27/2012, 11:55 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/27/2012, 7:56 pm
Re: Strip: Best sanding practices
dave g -- 2/27/2012, 10:09 pm
Re: Strip: Best sanding practices
Bill Hamm -- 2/27/2012, 2:02 am
Re: Strip: Best sanding practices
Scott Fitzgerrell -- 2/27/2012, 11:56 am
Re: Strip: Best sanding practices
Ian Johnson -- 2/26/2012, 6:37 pm