Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Tools: Can We Talk About Table Saws??
By:John Messinger
Date: 6/19/2012, 8:08 am
In Response To: Re: Tools: Can We Talk About Table Saws?? (Marc Upchurch)

: I find myself with 14 blades, I measured them recently to make a
: 1/8 slot for a specific project. Funny thing is that every slot
: I cut to measure was different. Which one should I pick?

Aside from an assortment of blade widths, it could be that you have one or two problems: 1.) bent/warped blades (letting them run too hot can cause them to warp permanently.) +/or 2.) excessive arbor runout, that you can check with a dial indicator:

http://en.wikipedia.org/wiki/Dial_indicator

Messages In This Thread

Tools: Can We Talk About Table Saws?? *PIC*
Kurt Maurer -- 6/18/2012, 1:47 pm
Re: Tools: Can We Talk About Table Saws??
Jay Babina -- 6/18/2012, 2:12 pm
Re: Tools: Can We Talk About Table Saws??
Bill Hamm -- 6/19/2012, 2:02 am
Re: Tools: Can We Talk About Table Saws??
Mike Bielski -- 6/18/2012, 2:15 pm
Re: Tools: Can We Talk About Table Saws??
Rod Tait (Orca Boats) -- 6/18/2012, 2:26 pm
Re: Tools: Can We Talk About Table Saws??
Etienne Muller -- 6/18/2012, 3:04 pm
Re: Tools: Can We Talk About Table Saws??
John Messinger -- 6/18/2012, 3:16 pm
Re: Tools: Can We Talk About Table Saws??
Deano -- 6/18/2012, 4:18 pm
Re: Tools: Can We Talk About Table Saws??
Mike Bielski -- 6/18/2012, 5:06 pm
Re: Tools: Can We Talk About Table Saws??
Etienne Muller -- 6/18/2012, 6:43 pm
Re: Tools: Can We Talk About Table Saws??
Marc Upchurch -- 6/18/2012, 9:55 pm
Re: Tools: Can We Talk About Table Saws??
Etienne Muller -- 6/19/2012, 3:27 am
Re: Tools: Can We Talk About Table Saws??
John Messinger -- 6/19/2012, 8:08 am
Re: Tools: Can We Talk About Table Saws??
Marc Upchurch -- 6/19/2012, 5:27 pm
Re: Tools: Can We Talk About Table Saws??
Mike Bielski -- 6/18/2012, 11:33 pm
Re: Tools: Can We Talk About Table Saws??
Marc Upchurch -- 6/18/2012, 5:19 pm
Re: Tools: Can We Talk About Table Saws??
Kurt Maurer -- 6/18/2012, 8:00 pm
Re: Tools: Can We Talk About Table Saws??
Jeff Horton -- 6/18/2012, 10:41 pm
Re: Tools: Can We Talk About Table Saws??
Allan -- 6/19/2012, 12:50 am
Re: Tools: Can We Talk About Table Saws??
Bill Hamm -- 6/19/2012, 1:33 am
Re: Tools: Can We Talk About Table Saws??
William Mayberry -- 6/18/2012, 9:51 pm
Re: Tools: Can We Talk About Table Saws??
danperry -- 6/18/2012, 10:44 pm
Re: Tools: Can We Talk About Table Saws??
danperry -- 6/18/2012, 11:06 pm
Re: Tools: Can We Talk About Table Saws??
Rob Macks/Laughing Loon CC&K -- 6/19/2012, 7:41 am
Re: Tools: Can We Talk About Table Saws?? *PIC*
Jeff Horton -- 6/19/2012, 12:47 pm
Thanks! Just made one for my saw
Rob Macks/Laughing Loon CC&K -- 6/21/2012, 11:08 am
Experience and Safety
Nick Schade - Guillemot Kayaks -- 6/19/2012, 9:20 am
Re: Experience and Safety
Al Edie -- 6/19/2012, 11:46 am
Re: Experience and Safety
Stephen Troy -- 6/19/2012, 2:45 pm
Re: Tools: Can We Talk About Table Saws??
Malcolm Schweizer -- 6/18/2012, 11:21 pm
Re: Tools: Can We Talk About Table Saws??
Bryan K -- 6/19/2012, 11:07 am
Do you mean "riving knife" or "splitter"?
Brian Nystrom -- 6/20/2012, 7:16 am
Here's a video that explains it
Brian Nystrom -- 6/20/2012, 7:19 am
Re: Do you mean "riving knife" or "splitter"?
John Abercrombie -- 6/20/2012, 2:41 pm
Re: Do you mean "riving knife" or "splitter"?
Brian Nystrom -- 6/21/2012, 6:56 am
Re: Tools: Can We Talk About Table Saws??
Rob Macks/Laughing Loon CC&K -- 6/20/2012, 8:40 am
Re: Tools: Can We Talk About Table Saws??
Mike M -- 6/20/2012, 8:46 am
Re: Tools: Can We Talk About Table Saws??
Will N 2 Go -- 6/21/2012, 12:44 am
Re: Tools: Can We Talk About Table Saws??
Scott Fitzgerrell -- 6/21/2012, 2:44 pm