Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Material: alu-tube rigidity
By:Bill Hamm
Date: 11/18/2012, 1:50 am
In Response To: Re: Material: alu-tube rigidity (Jeff Buyer)

: My build is simpler than yours because its not a folder. I simply
: used Tom Yost's method for laying out the frames for his
: folders. The holes drilled in the edges of the frames provide a
: recess for the tubes to sit in. The tubes will be epoxied to the
: plywood frames and then lashed.

: With your method of running carbon fiber through aluminum tubes I
: would worry about electrolysis. Aluminum is supposed to corrode
: when it contacts carbon fiber. You may need some kind of sleeve
: to prevent direct contact. Or perhaps some kind of plastic tube
: instead of aluminum.

: Torsion is twisting along the longitudinal axis. Imagine the
: right-hand side of the bow twisting up as the left-hand side of
: the stern also twists up. Obviously the left-hand side of the
: bow and the right-hand side of the stern will go down. This
: could be caused by paddling diagonally into large waves. An
: ordinary kayak is built strongly enough to resist torsion, and
: wood gunwales and stringers can tolerate some twisting, but
: ultra-light kayaks can twist quite a bit and this can cause
: sudden and catastrophic failure of pultruded carbon tubes. Platt
: Monfort designed a series of ultra-light small boats and used
: diagonal reinforcements with Kevlar roving to prevent torsion
: (www.gaboats.com). Clearly this method is not readily adaptable
: to folders.

: I don't have any pics up yet, but I will try to do so.

: Jeff

Platt's method might not work on folders using kevlar, but it certainly could be used with other high strength low stretch fibers like spectra.

Bill H.

Messages In This Thread

Material: alu-tube rigidity
CarstenT -- 11/14/2012, 3:26 pm
Re: Material: alu-tube rigidity
Marc Upchurch -- 11/14/2012, 6:55 pm
Re: Material: alu-tube rigidity
ancient kayaker -- 11/15/2012, 12:06 am
Re: Material: alu-tube rigidity
Bill Hamm -- 11/15/2012, 2:03 am
Re: Material: alu-tube rigidity
Brian Nystrom -- 11/15/2012, 7:18 am
Re: Material: alu-tube rigidity
Bill Hamm -- 11/16/2012, 10:22 am
Re: Material: alu-tube rigidity
Brian Nystrom -- 11/16/2012, 12:31 pm
Re: Material: alu-tube rigidity
CarstenT -- 11/16/2012, 5:32 pm
Re: Material: alu-tube rigidity
Marc Upchurch -- 11/16/2012, 9:22 pm
Re: Material: alu-tube rigidity
Bill Hamm -- 11/17/2012, 1:39 pm
Re: Material: alu-tube rigidity
Marc Upchurch -- 11/17/2012, 3:53 pm
Re: Material: alu-tube rigidity
Bill Hamm -- 11/18/2012, 12:35 am
Re: Material: alu-tube rigidity
Marc Upchurch -- 11/18/2012, 9:40 am
Re: Material: alu-tube rigidity
Bill Hamm -- 11/19/2012, 1:16 am
Re: Material: alu-tube rigidity
Mike Savage -- 11/17/2012, 3:54 pm
Re: Material: alu-tube rigidity
Marc Upchurch -- 11/17/2012, 7:07 pm
Re: Material: alu-tube rigidity
Bill Hamm -- 11/18/2012, 12:38 am
Re: Material: alu-tube rigidity
Mike Savage -- 11/18/2012, 12:42 pm
Re: Material: alu-tube rigidity
Yostwerks -- 11/15/2012, 11:06 am
Re: Material: alu-tube rigidity
CarstenT -- 11/15/2012, 12:22 pm
Re: Material: alu-tube rigidity
Yostwerks -- 11/15/2012, 1:42 pm
Re: Material: alu-tube rigidity *PIC*
Yostwerks -- 11/15/2012, 2:02 pm
Re: Material: alu-tube rigidity
CarstenT -- 11/15/2012, 3:04 pm
Re: Material: alu-tube rigidity
Bill Hamm -- 11/16/2012, 10:26 am
Re: Material: alu-tube rigidity
Jeff Buyer -- 11/15/2012, 11:11 am
Re: Material: alu-tube rigidity
CarstenT -- 11/15/2012, 12:51 pm
Re: Material: alu-tube rigidity
Bill Hamm -- 11/16/2012, 10:32 am
Re: Material: alu-tube rigidity
CarstenT -- 11/16/2012, 5:53 pm
Re: Material: alu-tube rigidity
Bill Hamm -- 11/17/2012, 1:42 pm
Re: Material: alu-tube rigidity
Bill Hamm -- 11/16/2012, 10:29 am
Re: Material: alu-tube rigidity
Jeff Buyer -- 11/16/2012, 11:21 am
Re: Material: alu-tube rigidity
Bill Hamm -- 11/17/2012, 1:44 pm
Re: Material: alu-tube rigidity
Jeff Buyer -- 11/17/2012, 3:53 pm
Re: Material: alu-tube rigidity
Bill Hamm -- 11/18/2012, 1:45 am
Re: Material: alu-tube rigidity
Jeff Buyer -- 11/18/2012, 1:56 pm
Re: Material: alu-tube rigidity
Bill Hamm -- 11/19/2012, 1:19 am
Re: Material: alu-tube rigidity
CarstenT -- 11/16/2012, 6:53 pm
Re: Material: alu-tube rigidity
Marc Upchurch -- 11/16/2012, 9:29 pm
Re: Material: alu-tube rigidity
CarstenT -- 11/17/2012, 5:30 am
Re: Material: alu-tube rigidity
Yostwerks -- 11/17/2012, 10:40 am
Re: Material: alu-tube rigidity
Bill Hamm -- 11/17/2012, 1:47 pm
Re: Material: alu-tube rigidity
Jeff Buyer -- 11/17/2012, 4:07 pm
Re: Material: alu-tube rigidity
CarstenT -- 11/17/2012, 4:34 pm
Re: Material: alu-tube rigidity
Jeff Buyer -- 11/17/2012, 5:40 pm
Re: Material: alu-tube rigidity
Bill Hamm -- 11/18/2012, 1:50 am
Re: Material: alu-tube rigidity
Jeff Buyer -- 11/18/2012, 2:10 pm
Re: Material: alu-tube rigidity
Bill Hamm -- 11/19/2012, 1:22 am
Re: Material: alu-tube rigidity
Bill Hamm -- 11/18/2012, 1:51 am
Re: Material: alu-tube rigidity
Jeff Buyer -- 11/18/2012, 2:07 pm
Re: Material: alu-tube rigidity
Bill Hamm -- 11/19/2012, 1:25 am
Re: Material: alu-tube rigidity *PIC*
Yostwerks -- 11/19/2012, 10:14 am
Re: Material: alu-tube rigidity
CarstenT -- 11/18/2012, 4:31 am
Electrolysis
CarstenT -- 6/2/2013, 6:39 am
Re: Electrolysis
Jeff Buyer -- 6/2/2013, 7:39 am
Re: Electrolysis
CarstenT -- 6/2/2013, 9:46 am
Re: Electrolysis
Tom Cooper -- 6/2/2013, 10:35 am
Re: Electrolysis
CarstenT -- 6/2/2013, 12:57 pm
Clogged up hinges. Solution
CarstenT -- 6/26/2013, 4:43 am
Re: Material: alu-tube rigidity
JohnAbercrombie -- 11/18/2012, 3:03 pm
Re: Material: alu-tube rigidity
Bill Hamm -- 11/19/2012, 1:33 am
Re: Material: alu-tube rigidity
Yostwerks -- 11/19/2012, 9:48 am
Re: Material: alu-tube rigidity
CarstenT -- 10/17/2014, 5:31 am
Re: Material: alu-tube rigidity
Bill Hamm -- 10/17/2014, 9:56 am
Re: Material: alu-tube rigidity
CarstenT -- 10/18/2014, 6:00 am