Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Strip: Problem Cutting strips
By:Thor
Date: 1/14/2013, 9:53 pm

This weekend I cut strips from western red cedar and Sitka spruce. I used the long fence on a skill saw method. I had two 18' x 8" WRC boards and one 17' x 7" Sitka board. The problem was both WRC boards cut strips that we're thinner in the middle than at the ends. I tried adjusting my technique but couldn't make a change. The worst strips are 3/16 at the ends and a fat 1/8 in the middle. I don't understand why both ends came out 3/16. If the fence was off I should have a problem that would progress from one end. Not one that appears and disappears. Unfortunately I did to take any pictures, but my setup was modeled after several posts like this http://forum.woodenboat.com/showthread.php?122305-Cutting-cedar-strips-I-swear-this-worked-before&p=2777248#post2777248 (if the link doesn't take you to the post it is #25)

Because the Sitka board hardly had the problem I wonder if the grain could cause an issue like this. Any ideas?

Thor

Messages In This Thread

Strip: Problem Cutting strips
Thor -- 1/14/2013, 9:53 pm
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/14/2013, 11:14 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/14/2013, 11:19 pm
Re: Strip: Problem Cutting strips
Allan -- 1/15/2013, 12:10 am
Re: Strip: Problem Cutting strips
Thor -- 1/15/2013, 2:49 pm
Re: Strip: Problem Cutting strips
Malcolm Schweizer -- 1/16/2013, 8:47 am
Re: Strip: Problem Cutting strips
Nick Riccardi -- 1/15/2013, 7:36 am
Re: Strip: Problem Cutting strips
Todd Olson -- 1/15/2013, 3:58 pm
Re: Strip: Problem Cutting strips
Kevin -- 1/15/2013, 7:15 pm
Re: Strip: Problem Cutting strips
Ken Blanton -- 1/15/2013, 8:51 pm
Re: Strip: Problem Cutting strips *PIC*
Jay Babina -- 1/16/2013, 4:08 pm
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/16/2013, 5:02 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/17/2013, 12:50 am
Re: Strip: Problem Cutting strips
Thor -- 1/16/2013, 5:25 pm
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/16/2013, 6:10 pm
Re: Strip: Problem Cutting strips
Allan -- 1/16/2013, 6:17 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/17/2013, 12:53 am
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 1:51 am
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/17/2013, 4:22 am
Re: Strip: Problem Cutting strips
Tom Thomas -- 1/17/2013, 8:44 am
Re: Strip: Problem Cutting strips *PIC*
John Abercrombie -- 1/17/2013, 12:05 pm
Re: Strip: Problem Cutting strips
Mike Savage -- 1/17/2013, 12:48 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 1:49 pm
Re: Strip: Problem Cutting strips
Mike Savage -- 1/18/2013, 2:19 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 1:53 pm
Re: Strip: Problem Cutting strips
Mike Savage -- 1/18/2013, 2:24 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 12:52 am
Re: Strip: Problem Cutting strips *PIC*
Rob Macks/Laughing Loon CC&K -- 1/19/2013, 9:03 am
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/17/2013, 2:30 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 11:44 am
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 12:45 am
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/19/2013, 4:24 am
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 4:50 am
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/19/2013, 10:46 am
Re: Strip: Problem Cutting strips *PIC*
Rob Macks/Laughing Loon CC&K -- 1/17/2013, 3:51 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 4:28 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 12:56 am
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/19/2013, 10:55 am
Re: Strip: Problem Cutting strips
PatrickC -- 1/17/2013, 7:17 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 8:07 pm
Re: Strip: Problem Cutting strips *PIC*
ancient kayaker -- 1/17/2013, 11:31 pm
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/19/2013, 12:16 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/19/2013, 8:36 pm
Re: Strip: Problem Cutting strips
Robert Horstmann -- 1/19/2013, 10:08 pm
Re: Strip: Problem Cutting strips
Tom Thomas -- 1/19/2013, 10:54 pm
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/20/2013, 4:32 am