Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: Problem Cutting strips
By:Allan
Date: 1/15/2013, 12:10 am
In Response To: Strip: Problem Cutting strips (Thor)

Was the edge of the board perfectly straight?

If it has even a very tiny bend, the convex side needs to go against the fence.

If the concave side is against the fence, you will get strips that are thin in the middle.

The longer your fence, the less concavity is needed to create a problem.

Messages In This Thread

Strip: Problem Cutting strips
Thor -- 1/14/2013, 9:53 pm
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/14/2013, 11:14 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/14/2013, 11:19 pm
Re: Strip: Problem Cutting strips
Allan -- 1/15/2013, 12:10 am
Re: Strip: Problem Cutting strips
Thor -- 1/15/2013, 2:49 pm
Re: Strip: Problem Cutting strips
Malcolm Schweizer -- 1/16/2013, 8:47 am
Re: Strip: Problem Cutting strips
Nick Riccardi -- 1/15/2013, 7:36 am
Re: Strip: Problem Cutting strips
Todd Olson -- 1/15/2013, 3:58 pm
Re: Strip: Problem Cutting strips
Kevin -- 1/15/2013, 7:15 pm
Re: Strip: Problem Cutting strips
Ken Blanton -- 1/15/2013, 8:51 pm
Re: Strip: Problem Cutting strips *PIC*
Jay Babina -- 1/16/2013, 4:08 pm
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/16/2013, 5:02 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/17/2013, 12:50 am
Re: Strip: Problem Cutting strips
Thor -- 1/16/2013, 5:25 pm
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/16/2013, 6:10 pm
Re: Strip: Problem Cutting strips
Allan -- 1/16/2013, 6:17 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/17/2013, 12:53 am
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 1:51 am
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/17/2013, 4:22 am
Re: Strip: Problem Cutting strips
Tom Thomas -- 1/17/2013, 8:44 am
Re: Strip: Problem Cutting strips *PIC*
John Abercrombie -- 1/17/2013, 12:05 pm
Re: Strip: Problem Cutting strips
Mike Savage -- 1/17/2013, 12:48 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 1:49 pm
Re: Strip: Problem Cutting strips
Mike Savage -- 1/18/2013, 2:19 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 1:53 pm
Re: Strip: Problem Cutting strips
Mike Savage -- 1/18/2013, 2:24 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 12:52 am
Re: Strip: Problem Cutting strips *PIC*
Rob Macks/Laughing Loon CC&K -- 1/19/2013, 9:03 am
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/17/2013, 2:30 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 11:44 am
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 12:45 am
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/19/2013, 4:24 am
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 4:50 am
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/19/2013, 10:46 am
Re: Strip: Problem Cutting strips *PIC*
Rob Macks/Laughing Loon CC&K -- 1/17/2013, 3:51 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 4:28 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 12:56 am
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/19/2013, 10:55 am
Re: Strip: Problem Cutting strips
PatrickC -- 1/17/2013, 7:17 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 8:07 pm
Re: Strip: Problem Cutting strips *PIC*
ancient kayaker -- 1/17/2013, 11:31 pm
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/19/2013, 12:16 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/19/2013, 8:36 pm
Re: Strip: Problem Cutting strips
Robert Horstmann -- 1/19/2013, 10:08 pm
Re: Strip: Problem Cutting strips
Tom Thomas -- 1/19/2013, 10:54 pm
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/20/2013, 4:32 am