Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: Problem Cutting strips *PIC*
By:John Abercrombie
Date: 1/17/2013, 12:05 pm
In Response To: Re: Strip: Problem Cutting strips (Tom Thomas)

As most of you probably know feather boards seem to be the norm but the constant adjusting would be a pain. I considered buying a power feeder but justifying that to the wife seemed to be too big of a ordeal. What I did find is a product that seems like it would be perfect for the job of feeding the planks through the blade and strips through the router. It's called the Micro Jig GGG-ripper , basically a hybrid push paddle. I bought 2 and I think it will work perfect. Another week or so and I'll be ready to cut my first strips and I'll report back my observations
http://m.youtube.com/results?q=ggg-ripper

This link should get you direct to the video:
http://www.youtube.com/watch?v=elocA26Nm5M

(haven't run across the m.youtube domain before).

I'm all for safety, and keep my fingers far away from the table saw blade.
Let us know how those '3-D Push Sticks' work out for ripping strips.

For a tool-and-jig-building-aholic, it's not difficult to make a spring-loaded featherboard for ripping strips.

I built something in a few minutes years ago and it has helped me to rip many hundred strips. I like to 'steer the board from 'well back' when ripping strips, and always use a ripping fence - aka 'short fence' for safety. You do need a (long) skinny push stick to shove the cut strip clear at the end. And, of course, a functional (usually temporary) outfeed table is another safety requirement, as it's pretty well impossible to hold down a 16-foot plank that's teetering over the back edge of the saw table.

Simpler, as mentioned, with a steel (better: cast iron) saw table, a magnetic featherboard is quick to adjust.

Let's all keep that finger count at a 'Perfect 10' !

Messages In This Thread

Strip: Problem Cutting strips
Thor -- 1/14/2013, 9:53 pm
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/14/2013, 11:14 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/14/2013, 11:19 pm
Re: Strip: Problem Cutting strips
Allan -- 1/15/2013, 12:10 am
Re: Strip: Problem Cutting strips
Thor -- 1/15/2013, 2:49 pm
Re: Strip: Problem Cutting strips
Malcolm Schweizer -- 1/16/2013, 8:47 am
Re: Strip: Problem Cutting strips
Nick Riccardi -- 1/15/2013, 7:36 am
Re: Strip: Problem Cutting strips
Todd Olson -- 1/15/2013, 3:58 pm
Re: Strip: Problem Cutting strips
Kevin -- 1/15/2013, 7:15 pm
Re: Strip: Problem Cutting strips
Ken Blanton -- 1/15/2013, 8:51 pm
Re: Strip: Problem Cutting strips *PIC*
Jay Babina -- 1/16/2013, 4:08 pm
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/16/2013, 5:02 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/17/2013, 12:50 am
Re: Strip: Problem Cutting strips
Thor -- 1/16/2013, 5:25 pm
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/16/2013, 6:10 pm
Re: Strip: Problem Cutting strips
Allan -- 1/16/2013, 6:17 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/17/2013, 12:53 am
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 1:51 am
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/17/2013, 4:22 am
Re: Strip: Problem Cutting strips
Tom Thomas -- 1/17/2013, 8:44 am
Re: Strip: Problem Cutting strips *PIC*
John Abercrombie -- 1/17/2013, 12:05 pm
Re: Strip: Problem Cutting strips
Mike Savage -- 1/17/2013, 12:48 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 1:49 pm
Re: Strip: Problem Cutting strips
Mike Savage -- 1/18/2013, 2:19 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 1:53 pm
Re: Strip: Problem Cutting strips
Mike Savage -- 1/18/2013, 2:24 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 12:52 am
Re: Strip: Problem Cutting strips *PIC*
Rob Macks/Laughing Loon CC&K -- 1/19/2013, 9:03 am
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/17/2013, 2:30 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 11:44 am
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 12:45 am
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/19/2013, 4:24 am
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 4:50 am
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/19/2013, 10:46 am
Re: Strip: Problem Cutting strips *PIC*
Rob Macks/Laughing Loon CC&K -- 1/17/2013, 3:51 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 4:28 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 12:56 am
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/19/2013, 10:55 am
Re: Strip: Problem Cutting strips
PatrickC -- 1/17/2013, 7:17 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 8:07 pm
Re: Strip: Problem Cutting strips *PIC*
ancient kayaker -- 1/17/2013, 11:31 pm
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/19/2013, 12:16 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/19/2013, 8:36 pm
Re: Strip: Problem Cutting strips
Robert Horstmann -- 1/19/2013, 10:08 pm
Re: Strip: Problem Cutting strips
Tom Thomas -- 1/19/2013, 10:54 pm
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/20/2013, 4:32 am