Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: Problem Cutting strips
By:Mike Savage
Date: 1/18/2013, 2:19 pm
In Response To: Re: Strip: Problem Cutting strips (John Abercrombie)

You are definitely welcome to the idea- I probably stole it from somebody else, and you can probably improve on it.

I was lucky to have a 'strong' spring around (spare from a guitar side bending machine); some dishwasher and oven door springs might work- though it is tough to 'visit the dump' (aka 'tip') nowadays, so 'shopping for parts' is more difficult.

The 'arm' out to the left (in the pic) is for clamping to the table (if you are ripping a wide board, you will still need to move the 'featherboard' from time-to-time) and I glued some 120 grit sandpaper to the underside to help prevent sliding on the saw table.

Nowadays I'm less 'fussy' about my tools, and I'll probably drill and tap a couple of holes in the saw table to anchor the featherboard, next time I rip strips. (this is all assuming I ever use up the pile of strips in the rack now....)

Cheers

Hi John,
I think Et uses washing machine springs with his set-up which is similar to yours.
Yeah, salvaging is getting harder, it's illegal in municipal recycle/dump here. Though that doesn't stop some from browsing.

I've already drilled the top of my tablesaw for a featherboard. But that limits me to 4-5 inch of stock width, hence my thinking of building a proper table for it. An dnicking as many ideas for it as possible. :D

Mike Savage
South West Cork

Messages In This Thread

Strip: Problem Cutting strips
Thor -- 1/14/2013, 9:53 pm
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/14/2013, 11:14 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/14/2013, 11:19 pm
Re: Strip: Problem Cutting strips
Allan -- 1/15/2013, 12:10 am
Re: Strip: Problem Cutting strips
Thor -- 1/15/2013, 2:49 pm
Re: Strip: Problem Cutting strips
Malcolm Schweizer -- 1/16/2013, 8:47 am
Re: Strip: Problem Cutting strips
Nick Riccardi -- 1/15/2013, 7:36 am
Re: Strip: Problem Cutting strips
Todd Olson -- 1/15/2013, 3:58 pm
Re: Strip: Problem Cutting strips
Kevin -- 1/15/2013, 7:15 pm
Re: Strip: Problem Cutting strips
Ken Blanton -- 1/15/2013, 8:51 pm
Re: Strip: Problem Cutting strips *PIC*
Jay Babina -- 1/16/2013, 4:08 pm
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/16/2013, 5:02 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/17/2013, 12:50 am
Re: Strip: Problem Cutting strips
Thor -- 1/16/2013, 5:25 pm
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/16/2013, 6:10 pm
Re: Strip: Problem Cutting strips
Allan -- 1/16/2013, 6:17 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/17/2013, 12:53 am
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 1:51 am
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/17/2013, 4:22 am
Re: Strip: Problem Cutting strips
Tom Thomas -- 1/17/2013, 8:44 am
Re: Strip: Problem Cutting strips *PIC*
John Abercrombie -- 1/17/2013, 12:05 pm
Re: Strip: Problem Cutting strips
Mike Savage -- 1/17/2013, 12:48 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 1:49 pm
Re: Strip: Problem Cutting strips
Mike Savage -- 1/18/2013, 2:19 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 1:53 pm
Re: Strip: Problem Cutting strips
Mike Savage -- 1/18/2013, 2:24 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 12:52 am
Re: Strip: Problem Cutting strips *PIC*
Rob Macks/Laughing Loon CC&K -- 1/19/2013, 9:03 am
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/17/2013, 2:30 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 11:44 am
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 12:45 am
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/19/2013, 4:24 am
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 4:50 am
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/19/2013, 10:46 am
Re: Strip: Problem Cutting strips *PIC*
Rob Macks/Laughing Loon CC&K -- 1/17/2013, 3:51 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 4:28 pm
Re: Strip: Problem Cutting strips
Bill Hamm -- 1/19/2013, 12:56 am
Re: Strip: Problem Cutting strips
ancient kayaker -- 1/19/2013, 10:55 am
Re: Strip: Problem Cutting strips
PatrickC -- 1/17/2013, 7:17 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/17/2013, 8:07 pm
Re: Strip: Problem Cutting strips *PIC*
ancient kayaker -- 1/17/2013, 11:31 pm
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/19/2013, 12:16 pm
Re: Strip: Problem Cutting strips
John Abercrombie -- 1/19/2013, 8:36 pm
Re: Strip: Problem Cutting strips
Robert Horstmann -- 1/19/2013, 10:08 pm
Re: Strip: Problem Cutting strips
Tom Thomas -- 1/19/2013, 10:54 pm
Re: Strip: Problem Cutting strips
Etienne Muller -- 1/20/2013, 4:32 am