Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: cove and bead router bits
By:Clayton Weed
Date: 10/12/2014, 10:12 am
In Response To: Strip: cove and bead router bits (Marc)

I used higher end brands only because they stay sharper longer. Most important thing I found was getting the right size for the thickness of the wood. Having two routers set up and good feather boards both side and top made it a breeze to run a lot of strips without changing the set up so all of the strips the same.

Messages In This Thread

Strip: cove and bead router bits
Marc -- 10/12/2014, 8:05 am
Re: Strip: cove and bead router bits
Clayton Weed -- 10/12/2014, 10:12 am
Re: Strip: cove and bead router bits
Marc Upchurch -- 10/12/2014, 10:32 am
Re: Strip: cove and bead router bits
Ric Allen -- 10/12/2014, 10:53 am
Re: Strip: cove and bead router bits
Ken Blanton -- 10/12/2014, 3:16 pm
Re: Strip: cove and bead router bits
Mochaboy -- 10/14/2014, 10:32 am
Re: Strip: cove and bead router bits
Gero Verheyen -- 10/14/2014, 11:38 am
Re: Strip: cove and bead router bits
JohnAbercrombie -- 10/14/2014, 1:20 pm
Re: Strip: cove and bead router bits
Mochaboy -- 10/14/2014, 2:04 pm
Re: Strip: cove and bead router bits
Gero Verheyen -- 10/14/2014, 2:16 pm
Re: Strip: cove and bead router bits
JohnAbercrombie -- 10/14/2014, 2:56 pm
Re: Strip: cove and bead router bits
JohnAbercrombie -- 10/14/2014, 3:04 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 4:40 pm
Re: Strip: cove and bead router bits
Gero Verheyen -- 10/14/2014, 5:07 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 5:13 pm
Re: Strip: cove and bead router bits
Gero Verheyen -- 10/14/2014, 5:23 pm
Re: Strip: cove and bead router bits
JohnAbercrombie -- 10/14/2014, 5:55 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 6:02 pm
Re: Strip: cove and bead router bits
JohnAbercrombie -- 10/14/2014, 6:29 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 5:57 pm
Re: Strip: cove and bead router bits
Ian Cummins -- 10/14/2014, 5:54 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 6:04 pm
Re: Strip: cove and bead router bits
JohnAbercrombie -- 10/14/2014, 6:27 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/15/2014, 12:43 am
Re: Strip: cove and bead router bits
Ken Blanton -- 10/14/2014, 7:03 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 8:24 pm
Re: Strip: cove and bead router bits
Ken Blanton -- 10/14/2014, 6:12 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 8:26 pm
Re: Strip: cove and bead router bits
scottbaxter -- 10/12/2014, 4:22 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/12/2014, 4:44 pm