Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: cove and bead router bits
By:Bill Hamm
Date: 10/14/2014, 5:57 pm
In Response To: Re: Strip: cove and bead router bits (Gero Verheyen)

With a zero clearance saw insert, that can be done, just have to make sure the feather boards are not binding the cut strip against the fence or it'll bind up the saw which is dangerous. Best and safest way is with a stock feeder which most of us don't have.

Bill H.

Messages In This Thread

Strip: cove and bead router bits
Marc -- 10/12/2014, 8:05 am
Re: Strip: cove and bead router bits
Clayton Weed -- 10/12/2014, 10:12 am
Re: Strip: cove and bead router bits
Marc Upchurch -- 10/12/2014, 10:32 am
Re: Strip: cove and bead router bits
Ric Allen -- 10/12/2014, 10:53 am
Re: Strip: cove and bead router bits
Ken Blanton -- 10/12/2014, 3:16 pm
Re: Strip: cove and bead router bits
Mochaboy -- 10/14/2014, 10:32 am
Re: Strip: cove and bead router bits
Gero Verheyen -- 10/14/2014, 11:38 am
Re: Strip: cove and bead router bits
JohnAbercrombie -- 10/14/2014, 1:20 pm
Re: Strip: cove and bead router bits
Mochaboy -- 10/14/2014, 2:04 pm
Re: Strip: cove and bead router bits
Gero Verheyen -- 10/14/2014, 2:16 pm
Re: Strip: cove and bead router bits
JohnAbercrombie -- 10/14/2014, 2:56 pm
Re: Strip: cove and bead router bits
JohnAbercrombie -- 10/14/2014, 3:04 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 4:40 pm
Re: Strip: cove and bead router bits
Gero Verheyen -- 10/14/2014, 5:07 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 5:13 pm
Re: Strip: cove and bead router bits
Gero Verheyen -- 10/14/2014, 5:23 pm
Re: Strip: cove and bead router bits
JohnAbercrombie -- 10/14/2014, 5:55 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 6:02 pm
Re: Strip: cove and bead router bits
JohnAbercrombie -- 10/14/2014, 6:29 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 5:57 pm
Re: Strip: cove and bead router bits
Ian Cummins -- 10/14/2014, 5:54 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 6:04 pm
Re: Strip: cove and bead router bits
JohnAbercrombie -- 10/14/2014, 6:27 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/15/2014, 12:43 am
Re: Strip: cove and bead router bits
Ken Blanton -- 10/14/2014, 7:03 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 8:24 pm
Re: Strip: cove and bead router bits
Ken Blanton -- 10/14/2014, 6:12 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/14/2014, 8:26 pm
Re: Strip: cove and bead router bits
scottbaxter -- 10/12/2014, 4:22 pm
Re: Strip: cove and bead router bits
Bill Hamm -- 10/12/2014, 4:44 pm