Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: S&G: Plate development
By:Hubert Schreier
Date: 12/6/2016, 1:03 am
In Response To: Re: S&G: Plate development (Bill Hamm)

I can't get into the math, but there seems to be an extra chine not marked on those lines at the bow and stern if I'm looking at it correctly.

Bill H.

There is no extra chine that is not marked, just two panels. Do you mean the rounded "soft" chine below the hard chine drawn in the plan? That is the result of the developable ruling and exactly what I am struggling with. I can only make it disappear if I introduce twist. The more twist, the less curvature. The cross sections on the right have less of this problem because there is 3 degrees of twist, but it is still visible.

Hubert.

Messages In This Thread

S&G: Plate development
Hubert Schreier -- 12/3/2016, 4:10 pm
Re: S&G: Plate development
upchurchmr -- 12/3/2016, 4:38 pm
Re: S&G: Plate development
Hubert Schreier -- 12/3/2016, 4:55 pm
Re: S&G: Plate development
upchurchmr -- 12/3/2016, 5:45 pm
Re: S&G: Plate development
Nick Schade - Guillemot Kayaks -- 12/3/2016, 10:14 pm
Re: S&G: Plate development
Hubert Schreier -- 12/4/2016, 12:57 am
Re: S&G: Plate development
upchurchmr -- 12/4/2016, 3:37 am
Re: S&G: Plate development
Hubert Schreier -- 12/4/2016, 11:45 pm
Re: S&G: Plate development
Alex Ferguson -- 12/5/2016, 3:38 pm
Re: S&G: Plate development
upchurchmr -- 12/5/2016, 5:42 pm
Re: S&G: Plate development
Hubert Schreier -- 12/5/2016, 9:23 pm
Re: S&G: Plate development
Alex Ferguson -- 12/5/2016, 9:55 pm
Re: S&G: Plate development
Hubert Schreier -- 12/6/2016, 12:34 am
Re: S&G: Plate development
Nick Schade - Guillemot Kayaks -- 12/4/2016, 8:20 am
Re: S&G: Plate development *PIC*
Hubert Schreier -- 12/5/2016, 10:23 pm
Re: S&G: Plate development
Bill Hamm -- 12/6/2016, 12:56 am
Re: S&G: Plate development
Hubert Schreier -- 12/6/2016, 1:03 am
Re: S&G: Plate development
Bill Hamm -- 12/6/2016, 1:09 am
Re: S&G: Plate development
Hubert Schreier -- 12/6/2016, 1:20 am
Re: S&G: Plate development
Mike Bielski -- 12/6/2016, 1:09 pm
Re: S&G: Plate development *PIC*
Hubert Schreier -- 12/6/2016, 3:07 pm
Re: S&G: Plate development
Mike Bielski -- 12/6/2016, 4:35 pm
Re: S&G: Plate development
upchurchmr -- 12/6/2016, 7:14 am
Re: S&G: Plate development
Hubert Schreier -- 12/6/2016, 8:45 am
Re: S&G: Plate development
Nick Schade - Guillemot Kayaks -- 12/6/2016, 8:49 am
Re: S&G: Plate development
Hubert Schreier -- 12/6/2016, 10:04 am
Re: S&G: Plate development
upchurchmr -- 12/6/2016, 11:04 am
Re: S&G: Plate development *PIC*
Nick Schade - Guillemot Kayaks -- 12/6/2016, 7:29 pm
Re: S&G: Plate development
Hubert Schreier -- 12/6/2016, 8:26 pm
Re: S&G: Plate development *PIC*
Hubert Schreier -- 12/7/2016, 12:27 am
Re: S&G: Plate development
Nick Schade - Guillemot Kayaks -- 12/7/2016, 7:45 am
Re: S&G: Plate development
upchurchmr -- 12/7/2016, 9:29 am
Re: S&G: Plate development
Nick Schade - Guillemot Kayaks -- 12/7/2016, 10:21 am
Re: S&G: Plate development
upchurchmr -- 12/7/2016, 12:43 pm
Re: S&G: Plate development *PIC*
Hubert Schreier -- 12/13/2016, 4:00 am
Re: S&G: Plate development *PIC*
Nick Schade - Guillemot Kayaks -- 12/13/2016, 6:54 pm
Re: S&G: Plate development
Hubert Schreier -- 12/13/2016, 8:03 pm
Re: S&G: Plate development *PIC*
Nick Schade - Guillemot Kayaks -- 12/13/2016, 11:10 pm
Re: S&G: Plate development
Hubert Schreier -- 12/30/2016, 6:08 pm
Re: S&G: Plate development *PIC*
Dan Caouette (CSCWC) -- 12/14/2016, 6:55 am
Delftship
Nick Schade - Guillemot Kayaks -- 12/14/2016, 8:50 am
Re: Delftship *PIC*
Dan Caouette (CSCWC) -- 12/14/2016, 11:57 am
Re: Delftship
Nick Schade - Guillemot Kayaks -- 1/25/2017, 9:41 am
Re: Delftship
Dan Caouette (CSCWC) -- 1/25/2017, 6:19 pm
Re: S&G: Plate development
Hubert Schreier -- 12/30/2016, 5:53 pm
Re: S&G: Plate development
Dan Caouette (CSCWC) -- 12/31/2016, 8:57 am
Find "MultiConic Dev of Hull Surfaces"
mick allen -- 12/5/2016, 8:16 pm
Re: Find "MultiConic Dev of Hull Surfaces"
Hubert Schreier -- 12/5/2016, 11:07 pm