Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: 2 X 4 's into strips
By:Steve Solomon
Date: 1/4/2017, 9:22 am
In Response To: Strip: 2 X 4 's into strips (Richard Mertins)

This may be a dumb suggestion, but just throwing it out there. Your old 2x4s are true "2 inch by 4 inch," right? So what if you used Rob's method (with any errors my own) as follows:

1) run through the jointer on a 2" side to get one clean face
2) Set up the saw for 3/4", and with that cleaned up edge against the fence, run through table saw cutting 3/4" x 2" billets, if I'm doing the calculations right with a 1/8" kerf you should get four billets per board with a bit less than 1/4" waste which could potentially be planed and cut into a viable strip
3) If necessary, run each billet through the jointer to clean up a 3/4" face
4) Run each billet through the table saw to cut the 3/16" x 3/4" strips - I think you should get 7 strips per billet = 28 strips per board plus the one bonus strip from the waste

Messages In This Thread

Strip: 2 X 4 's into strips
Richard Mertins -- 1/3/2017, 6:41 pm
Re: Strip: 2 X 4 's into strips
Marc Upchurch -- 1/3/2017, 8:36 pm
Re: Strip: 2 X 4 's into strips
Bill Hamm -- 1/3/2017, 11:54 pm
Re: Strip: 2 X 4 's into strips
Richard Mertins -- 1/4/2017, 7:52 am
Re: Strip: 2 X 4 's into strips
Marc Upchurch -- 1/4/2017, 9:53 am
Re: Strip: 2 X 4 's into strips
Steve Solomon -- 1/4/2017, 11:07 am
Re: Strip: 2 X 4 's into strips
Marc Upchurch -- 1/4/2017, 11:59 am
Re: Strip: 2 X 4 's into strips
Steve Solomon -- 1/4/2017, 12:56 pm
Re: Strip: 2 X 4 's into strips
Bill Hamm -- 1/5/2017, 12:23 am
Re: Strip: 2 X 4 's into strips
Steve Solomon -- 1/5/2017, 7:05 am
Overthinking
Curtis Fisher -- 1/5/2017, 8:16 pm
Re: Overthinking
Steve Solomon -- 1/6/2017, 12:12 am
Re: Strip: 2 X 4 's into strips
Bill Hamm -- 1/6/2017, 3:12 am
Re: Strip: 2 X 4 's into strips
David Wyse -- 1/4/2017, 12:01 pm
Re: Strip: 2 X 4 's into strips
Steve Solomon -- 1/4/2017, 9:22 am
Re: Strip: 2 X 4 's into strips
Nick R. -- 1/4/2017, 4:18 pm
Re: Strip: 2 X 4 's into strips
Rob Macks/Laughing Loon CC&K -- 1/5/2017, 9:06 am
Re: Strip: 2 X 4 's into strips
JohnAbercrombie -- 1/7/2017, 11:16 am
Re: Strip: 2 X 4 's into strips
Richard Mertins -- 1/7/2017, 11:34 am
Re: Strip: 2 X 4 's into strips
Rob Macks/Laughing Loon CC&K -- 1/7/2017, 11:50 am
Re: Strip: 2 X 4 's into strips
Richard Mertins -- 1/8/2017, 7:32 am
Re: Strip: 2 X 4 's into strips
Marc Upchurch -- 1/8/2017, 8:55 am
Re: Strip: 2 X 4 's into strips
dave koslow -- 1/9/2017, 2:11 pm
Re: Strip: 2 X 4 's into strips
Marc Upchurch -- 1/9/2017, 5:18 pm
Re: Strip: 2 X 4 's into strips
Bill Hamm -- 1/9/2017, 1:20 am