Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Tools: Recommendations?
By:Steve Solomon
Date: 1/19/2017, 2:08 pm
In Response To: Re: Tools: Recommendations? (Rob Macks/Laughing Loon CC&K)

3/4" wide strips work well for most designs with such small facets joint angles are miniscule.

Rob, I'm not arguing with you I just don't fully understand your answer. If I have two strips coming together at an angle, that creates a "corner" along the edge. With a small joint angle, that's a very minimal high spot - less than 1/16". If I sand down that 1/16", easing the corner, then there's (probably) still a flat area in the middle of the strip. Are you saying:
a) with a 3/4" strip and shallow angle, that's a satisfactory result, no need to remove any more material
or
b) you can't just ease the high spot, you need to keep sanding with the 50 grit until the entire width of the strip has been rounded over at least a little and no flat spots remain

In any case - I'll let it go at this point.

Messages In This Thread

Tools: Recommendations?
Patrick North -- 1/16/2017, 7:23 pm
Re: Tools: Recommendations?
Mike Bielski -- 1/16/2017, 7:48 pm
Re: Tools: Recommendations?
Mike Bielski -- 1/16/2017, 7:49 pm
Re: Tools: Recommendations?
Marc Upchurch -- 1/16/2017, 7:50 pm
Re: Tools: Recommendations?
scottbaxter -- 1/16/2017, 9:23 pm
Re: Tools: Recommendations?
Dan Caouette (CSCWC) -- 1/17/2017, 7:30 am
Surform
jaybabina -- 1/17/2017, 8:12 am
Re: Surform
Jim777 -- 1/21/2017, 6:28 am
Re: Tools: Recommendations? *PIC*
Etienne Muller -- 1/17/2017, 8:45 am
Re: Tools: Recommendations?
Nick R. -- 1/17/2017, 9:38 am
Re: Tools: Recommendations?
Rich D -- 1/17/2017, 9:42 am
Re: Tools: Recommendations?
Rob Macks/Laughing Loon CC&K -- 1/17/2017, 10:55 am
Re: Tools: Recommendations?
Patrick North -- 1/18/2017, 9:42 am
Re: Tools: Recommendations?
Steve Solomon -- 1/18/2017, 12:32 pm
Re: Tools: Recommendations?
Patrick North -- 1/18/2017, 12:56 pm
Re: Tools: Recommendations?
Steve Solomon -- 1/18/2017, 1:38 pm
Re: Tools: Recommendations?
Marc Upchurch -- 1/18/2017, 3:47 pm
Re: Tools: Recommendations?
Rob Macks/Laughing Loon CC&K -- 1/18/2017, 1:44 pm
Re: Tools: Recommendations?
Steve Solomon -- 1/19/2017, 10:26 am
Re: Tools: Recommendations?
Rob Macks/Laughing Loon CC&K -- 1/19/2017, 11:54 am
Re: Tools: Recommendations?
Steve Solomon -- 1/19/2017, 12:23 pm
Re: Tools: Recommendations?
Rob Macks/Laughing Loon CC&K -- 1/19/2017, 1:06 pm
Re: Tools: Recommendations?
Steve Solomon -- 1/19/2017, 2:08 pm
Re: Tools: Recommendations?
Rob Macks/Laughing Loon CC&K -- 1/19/2017, 3:22 pm
Re: Tools: Recommendations?
Etienne Muller -- 1/19/2017, 4:42 pm
Re: Tools: Recommendations?
Steve Solomon -- 1/19/2017, 5:22 pm
Re: Tools: Recommendations?
Marc Upchurch -- 1/19/2017, 5:42 pm
Re: Tools: Recommendations?
Steve Solomon -- 1/19/2017, 6:01 pm
Re: Tools: Recommendations?
Etienne Muller -- 1/19/2017, 6:09 pm
Re: Tools: Recommendations?
Steve Solomon -- 1/19/2017, 6:42 pm
Re: Tools: Recommendations?
Justin -- 1/20/2017, 5:25 am
Re: Tools: Recommendations?
Steve Solomon -- 1/20/2017, 6:45 am
Re: Tools: Recommendations?
Rob Macks/Laughing Loon CC&K -- 1/20/2017, 8:57 am
Re: Tools: Recommendations?
Etienne Muller -- 1/20/2017, 3:10 pm
Re: Tools: Recommendations?
Bob Ten Eyck -- 1/22/2017, 12:13 pm
Fair ?
jaybabina -- 1/19/2017, 11:56 am
Re: Fair ?
Patrick North -- 1/19/2017, 12:20 pm
Re: Fair ?
Steve Solomon -- 1/19/2017, 12:39 pm
Re: Fair ?
scottbaxter -- 1/19/2017, 4:28 pm
Re: Fair ?
Steve Solomon -- 1/19/2017, 5:43 pm
Re: Fair ?
Bill Hamm -- 1/20/2017, 12:08 am
Re: Fair ?
Steve Solomon -- 1/20/2017, 6:37 am
Re: Fair ?
Dan Caouette (CSCWC) -- 1/19/2017, 5:10 pm
Re: Fair ?
Marc Upchurch -- 1/19/2017, 5:45 pm
Re: Fair ?
Mike Bielski -- 1/19/2017, 10:45 pm
Re: Tools: ROS and neighbours
Ian Johnson -- 1/22/2017, 9:32 pm
Re: Tools: ROS and neighbours
anewhouse -- 1/22/2017, 10:19 pm
Fair
Les Cheeseman -- 1/29/2017, 10:40 am