Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: WoodenBoat Bird's Mouth Paddle Shaft
By:TomRobb
Date: 7/28/2000, 10:27 am
In Response To: Re: WoodenBoat Bird's Mouth Paddle Shaft (Shawn B)

RE: glass or carbon fiber inside the shaft. Why? All the tension stress is on the aft/outside of the shaft. Why core it with foam? The hollow air core is lighter. And plugs in the end keep the water out and make a transition between the beam loaded shaft and the blade. Why glass/carbon/wood composit at all? It only serves to make it heavier. Wood IS a composit.
: Yes. Set the blade so its inside edge is just under the rip fence. Note that
: you must have a zero-clearance table insert so the blade doesn't pull the
: skinny strip down into the slot. Set the blade at 45* and raise it until
: the edge of the kerf is right at the center of the strip. Rip the strip,
: then flip the board end-for end and cut it again to clear out the rabbet.

: No, the second pass will clear out the small vee left by the top of the blade
: in the first cut. But, a blade with square-sided teeth will give you a
: smoother cut.

: I plan to attach a solid glass blade, so attachment will be via thickened
: epoxy to the back of the blade. A wood blade would be a bit more difficult
: and take some creativity--but it wouldn't be impossible!

: Happy building, Shawn

Messages In This Thread

WoodenBoat Bird's Mouth Paddle Shaft *Pic*
Shawn B -- 7/27/2000, 10:32 am
Re: Good Going Shawn!! *Pic*
Bill Boyd -- 7/30/2000, 9:04 pm
Blade Idea
mike allen ---> -- 7/31/2000, 5:52 pm
Re: Why stop there? *Pic*
Bill Boyd -- 8/1/2000, 11:22 am
Re: Why stop there?
Shawn B -- 8/1/2000, 1:36 pm
Re: Thank you Shawn!
Bill Boyd -- 8/1/2000, 8:26 pm
Don't you know where to stop?????
mike allen ---> -- 8/1/2000, 12:36 pm
Re: Blade Idea - Like for Kent Boutillier
mike allen ---> -- 7/31/2000, 7:28 pm
Lamenting le LE lost, lonely & leftout - (nt)
mike allen ---> -- 7/31/2000, 7:42 pm
Re: Good Going Shawn!!
Ross Leidy -- 7/31/2000, 10:14 am
Re: Good Going Shawn!!
Bill Boyd -- 7/31/2000, 11:49 am
Seal the inside with epoxy
Dale Frolander -- 7/28/2000, 2:39 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Spidey -- 7/27/2000, 5:08 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Mike Nicholson -- 7/27/2000, 5:35 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Shawn B -- 7/27/2000, 6:49 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
TomRobb -- 7/28/2000, 10:27 am
Re: WoodenBoat Bird's Mouth Paddle Shaft
Shawn B -- 7/27/2000, 5:26 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Spidey -- 7/27/2000, 6:21 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Ron Eike -- 7/28/2000, 7:37 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Rehd -- 7/27/2000, 1:20 pm
Re: Possible failure?
Shawn B -- 7/27/2000, 2:50 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Rob Forsell -- 7/27/2000, 12:57 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Don Beale -- 7/27/2000, 12:28 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Shawn B -- 7/27/2000, 12:58 pm
Re:I have to disagree with the crowd
Don Beale -- 7/28/2000, 12:05 am
Re: WoodenBoat Bird's Mouth Paddle Shaft
Mike Hanks -- 7/27/2000, 1:32 pm
Re: Got weep holes?
Shawn B -- 7/27/2000, 1:52 pm
eliminate the need for weepholes
Paul G. Jacobson -- 7/28/2000, 1:08 am
Re: Got weep holes?
Craig Doyle -- 7/27/2000, 2:59 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
peter czerpak -- 7/27/2000, 12:13 pm
Re: Composite cored Bird's Mouth
Shawn B -- 7/27/2000, 12:56 pm
Re: Composite cored Bird's Mouth
Nick Schade - Guillemot Kayaks -- 7/28/2000, 10:12 am
Possible composite core technique
Paul G. Jacobson -- 7/28/2000, 12:56 am
Re: Composite cored Bird's Mouth
Bill Boyd -- 7/27/2000, 9:36 pm
Re: Hollow core=Brilliant!
Shawn Baker -- 7/28/2000, 12:29 am
Re: yup *Pic*
Bill Boyd -- 7/29/2000, 4:00 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Mike Hanks -- 7/27/2000, 11:05 am
Re: WoodenBoat Bird's Mouth Paddle Shaft
Shawn B -- 7/27/2000, 1:01 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
j -- 7/28/2000, 3:51 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Jason -- 7/28/2000, 4:26 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
jtmc -- 7/28/2000, 11:38 pm
Re: Twist in Bird's Mouth
Shawn B -- 7/28/2000, 4:22 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Ross Leidy -- 7/27/2000, 10:44 am