Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Don't you know where to stop?????
By:mike allen --->
Date: 8/1/2000, 12:36 pm
In Response To: Re: Why stop there? *Pic* (Bill Boyd)

: Gee Mick

: I was thinking about you when I was looking for something smaller to use as a
: support for the innertube... vinyl coated clothsline tied to the rear
: bumper of my rambler or something. Anyway I made a small sample of some
: 1/8" thick cedar and found it didn't work so well eight sided ..but
: ten sided and a 54 degree cut I got something I will have to try . Maybe I
: could put Nicads in each end with mercury switchs and bright L.E.D 's so
: the blade that was in the air would be lit and a small solar cell on each
: blade for recharging in the daytime when the paddle was stored
: horizontal,it would kinda be like those running shoes. Or make provisions
: for those pulleys they use on compound bows and string it with Dacron for
: launching small harpoons at those orcas that mistake you for a large
: surface plug...WWWWHOOOA ... that cedar really is toxic!!

: Later

: Bill

Amazing work, would make a great thin, light shaft. And with no twist would give about 72 deg off set if you used my previous post.

As for the hummer cable idea, what about 1in od tubing(garden hose, pvc soft or pvc hard(??)) tied to the back of the rambler gently idling, no internal copper tube. After setup, reverse the pump and deflate the tube, tie off the ends(strong twine, fishing line) and remove? That way you could maybe sqeeze it a bit differentially for the diff hand positions(oval at the hands).

But I'm serious, that splaying the ends of the shaft to outline or intertwine w/ the blade would be kinda cool.

-mick

Messages In This Thread

WoodenBoat Bird's Mouth Paddle Shaft *Pic*
Shawn B -- 7/27/2000, 10:32 am
Re: Good Going Shawn!! *Pic*
Bill Boyd -- 7/30/2000, 9:04 pm
Blade Idea
mike allen ---> -- 7/31/2000, 5:52 pm
Re: Why stop there? *Pic*
Bill Boyd -- 8/1/2000, 11:22 am
Re: Why stop there?
Shawn B -- 8/1/2000, 1:36 pm
Re: Thank you Shawn!
Bill Boyd -- 8/1/2000, 8:26 pm
Don't you know where to stop?????
mike allen ---> -- 8/1/2000, 12:36 pm
Re: Blade Idea - Like for Kent Boutillier
mike allen ---> -- 7/31/2000, 7:28 pm
Lamenting le LE lost, lonely & leftout - (nt)
mike allen ---> -- 7/31/2000, 7:42 pm
Re: Good Going Shawn!!
Ross Leidy -- 7/31/2000, 10:14 am
Re: Good Going Shawn!!
Bill Boyd -- 7/31/2000, 11:49 am
Seal the inside with epoxy
Dale Frolander -- 7/28/2000, 2:39 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Spidey -- 7/27/2000, 5:08 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Mike Nicholson -- 7/27/2000, 5:35 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Shawn B -- 7/27/2000, 6:49 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
TomRobb -- 7/28/2000, 10:27 am
Re: WoodenBoat Bird's Mouth Paddle Shaft
Shawn B -- 7/27/2000, 5:26 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Spidey -- 7/27/2000, 6:21 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Ron Eike -- 7/28/2000, 7:37 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Rehd -- 7/27/2000, 1:20 pm
Re: Possible failure?
Shawn B -- 7/27/2000, 2:50 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Rob Forsell -- 7/27/2000, 12:57 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Don Beale -- 7/27/2000, 12:28 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Shawn B -- 7/27/2000, 12:58 pm
Re:I have to disagree with the crowd
Don Beale -- 7/28/2000, 12:05 am
Re: WoodenBoat Bird's Mouth Paddle Shaft
Mike Hanks -- 7/27/2000, 1:32 pm
Re: Got weep holes?
Shawn B -- 7/27/2000, 1:52 pm
eliminate the need for weepholes
Paul G. Jacobson -- 7/28/2000, 1:08 am
Re: Got weep holes?
Craig Doyle -- 7/27/2000, 2:59 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
peter czerpak -- 7/27/2000, 12:13 pm
Re: Composite cored Bird's Mouth
Shawn B -- 7/27/2000, 12:56 pm
Re: Composite cored Bird's Mouth
Nick Schade - Guillemot Kayaks -- 7/28/2000, 10:12 am
Possible composite core technique
Paul G. Jacobson -- 7/28/2000, 12:56 am
Re: Composite cored Bird's Mouth
Bill Boyd -- 7/27/2000, 9:36 pm
Re: Hollow core=Brilliant!
Shawn Baker -- 7/28/2000, 12:29 am
Re: yup *Pic*
Bill Boyd -- 7/29/2000, 4:00 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Mike Hanks -- 7/27/2000, 11:05 am
Re: WoodenBoat Bird's Mouth Paddle Shaft
Shawn B -- 7/27/2000, 1:01 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
j -- 7/28/2000, 3:51 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Jason -- 7/28/2000, 4:26 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
jtmc -- 7/28/2000, 11:38 pm
Re: Twist in Bird's Mouth
Shawn B -- 7/28/2000, 4:22 pm
Re: WoodenBoat Bird's Mouth Paddle Shaft
Ross Leidy -- 7/27/2000, 10:44 am